EM8605 Basic Wireless GSM Alarm System Starter Kit
| ENGLISH EM8605 - Basic Wireless GSM Alarm System Starter Kit Table of contents 1.0 Introduction ........................................................................................................... 4 1.1 Packing contents ............................................................................................... 4 2.0 Explanation of the Alarm system ........................................................................... 4 2.1 Front ..........................................................
| ENGLISH 7.0 Remote control .................................................................................................... 26 7.1 Front of remote control .................................................................................... 26 7.2 Arm the alarm .................................................................................................. 26 7.3 Disarm the alarm ............................................................................................. 27 7.4 In-home mode .....
| ENGLISH 1.0 Introduction Congratulations with the purchase of this high-quality Eminent product! This product has undergone extensive testing by Eminent’s technical experts. Should you experience any problems with this product; you are covered by a five-year Eminent warranty. Please keep this manual and the receipt in a safe place. Register your product now on www.eminent-online.com and receive product updates! 1.
| ENGLISH 1. Quick flashing green: Searching GSM network Slow flashing green: Normal GSM signal Red: Pairing mode Quick flashing red: Alarm 2.
| ENGLISH 2.2 Rear 1. SIM Card slot 2. Pairing button 3. Power On/Off 4. Power adapter interface 3.0 Preparation 3.1 GSM SIM card To get the best out of the system, it is crucial to take some precautions before making use of the alarm system. The EM8605 alarm system will send you a text message or gives you a call when there is an alarm. In order to do so, the system needs a SIM card from a mobile phone provider.
| ENGLISH 3.2 Download APP The EM8605 system can be set and operated with an APP, but it can also be fully used with SMS commands. The APP is only available for Android and Apple (iOS) phones. Search for the "EM8605" APP in the Google Play store or the Apple Store. See chapter "Apple and Android APP" for more information on the operation of the APP 3.3 Plan for sensor placement Before starting to install the alarm system it is important to make a plan.
| ENGLISH 1. 2. 3. 4. 5. 6. 7. 8. Front door : Window/door contact Living room : Motion detector PIR Window - Living room : Window/door contact Window - Living room : Window/door contact Door-terrace : Window/door contact Window – Bedroom : window/door contact Bedroom : Motion detector PIR Kitchen : Gas detector Check www.eminent-online.com for an overview of all available sensors and accessories. 3.
| ENGLISH The default jumper settings for a window/door contact are D0, D1 and D2 (Normalgroup), for the motion detector the default settings are D1 and D2 (Home-group).This means that the window/door contact will be enabled when the alarm system is in full security mode or in-home security. The motion detector will only be enabled when the alarm system is in full security mode. You can enable the full or in-home security by using the Alarm system, remote control, the EM8605 APP or your mobile phone.
| ENGLISH 3.7 Register wireless siren The wireless siren is an extra accessory. To register the siren to the system press shortly the connect button of the siren. The LED will turn on. Press the “SOS” of the control panel. You will hear a beep to notify you the registration is successful. 4.0 Operating the Alarm System 4.1 Change language Send a text message with the text 0001 to the alarm system. The language will be set to English. 0001 Operate successfully.
| ENGLISH 0033 Opération réussi avec succès. Send a text message with the text 0039 to the alarm system. The language will be set to Italian. 0039 Avvenuto Correttamente. The language can also be modified by using the “EM8605” APP. This App is explained in chapter 5.
| ENGLISH 4.2 Text message commands All settings of the system can be controlled and configured by sending text messages to the system. Before you power up the alarm system install a mobile SIM card first. Notice: make sure the PIN and voicemail of the SIM card are both disabled. You can disable this by using the SIM card in a regular mobile phone. In case of a prepaid card make sure you have enough credit on the SIM card. Install the SIM card in the alarm system.
| ENGLISH 4.4 Arm the alarm system In the first part of the menu (?) you see the command that’s needed to arm the system (1). You only need to send a text message to the SIM card of the alarm system with the text 1. You will receive a text message to confirm the system is armed (System armed). 1 System armed. 4.5 Call-back monitor When you send a text message to the SIM card of the alarm system with the text 2. The alarm system will call you back.
| ENGLISH 5.1 Add an account With the APP you can control the alarm system. The Apple APP will create a text message with the command needed to configure the settings. After this the message needs to be send manually. Press send to send the message. If used with an Android device the text message will be send automatically. 1. Start the APP on your phone and select ‘Add Account’ 2.
| ENGLISH 4. After you have selected the account you will see the Alarm system. With the Alarm system you can control the alarm system. To enter the settings menu you need to swipe the screen to the left. 5.2 Delete an account To delete an account, there are different methods for Apple and Android. 5.2.1 Delete an account on an Apple phone (iOS) Press the edit button on the screen where the accounts are added. On the left side of the account a minus sign will appear.
| ENGLISH 5.3 Secure the APP with a PIN/Passcode The APP has the possibility to secure the access to the APP and settings with a Passcode. Follow the instructions below to set this security feature.
| ENGLISH • Enter a 4 digit PIN/Passcode you wish to use to access the APP • Repeat the PIN/Passcode for verification • Restart the APP and you will be prompted to enter the PIN/Passcode.
| ENGLISH 5.4 Control the alarm system Below you will find an explanation of each function. Disarm the alarm system Arm the alarm system Call-back monitor 5.5 Configure the alarm system by using the APP The configuration of the alarm system is done by sending text messages to the SIM card of the alarm system or by using the APP. In chapter 6 you will find information about how to configure the alarm system. Both ways of configuration, text messages and APP, will be explained. 6.
| ENGLISH 3 TEL: 1. 2. 3. 4. 5. Copy above text into a new text message, modify the text and send the text message to the GSM-number of the alarm system: TEL: 1.00446123654789 2.00446333222558 3.00446223366998 4.00446557788112 5.00446552233668 Store phone numbers successfully.
| ENGLISH 6.2 Alarm notifications The alarm system will check the programmed phone numbers one by one. Firstly every number will get a text message. When this is fulfilled the alarm system will start calling the programmed numbers. If one of the phone number has the voicemail enabled the system will continue to call the next phone number. Between every text message and phone call there will be a time span of approximately 15 seconds.
| ENGLISH Change zone information successfully. With the EM8605 APP: 6.4 Low battery warning of a sensor by text message Notice: This function is only available for sensors with a 2-way communication (example: EM8650). You will receive a text message when the battery level is low. The message will have the following information in the text message: The sensor name (Up to sensor 4) and the text ‘Battery low’.
| ENGLISH 5 Alarm delay time (0-300sec): 0 Copy above text into a new text message, modify the text and send the text message to the GSM-number of the alarm system: Alarm delay time (0-300sec): 30 Set alarm delay time successfully.
| ENGLISH 6.7 Adjust siren volume and time of alarm Both settings can be adjusted by this menu. 6 Siren volume (0 Mute, 1 Low, 2 Medium, 3 High): 2 Siren ringing time (1-9 min):5 Copy above text into a new text message, modify the text and send the text message to the GSM-number of the alarm system: Siren volume (0 Mute, 1 Low, 2 Medium, 3 High): 1 Siren ringing time (1-9 min): 4 Set siren volume and ringing time successfully.
| ENGLISH 6.8 Restore factory defaults. Also called hard reset. This needs to be done when, for example, a new SIM card is installed. Push the button on the back of the alarm system and press the SOS button on the alarm system simultaneously. Wait for 3 beeps to confirm the Alarm system has been restored to factory defaults. 6.
| ENGLISH 6.11 Turn off the operation indicator LED The operation indication LED on the side panel of the alarm system can be switched off by sending a text message to the alarm system. 30 6.12 Turn on the operation indicator LED The operation indication LED on the side panel of the alarm system can be switched on by sending a text message to the alarm system.
| ENGLISH 31 7.0 Remote control 7.1 Front of remote control LED Indicator Arm In-home security Disarm Panic button 7.2 Arm the alarm Press to arm the alarm. The LED indicator will light up shortly and the siren will give a short beep to confirm the system is active.
| ENGLISH 7.3 Disarm the alarm Press to disarm the alarm. The LED indicator will light up shortly and the siren will beep 2 times to confirm the system is disarmed. 7.4 In-home mode Press . All sensors configured in the normal-group will be enabled; the sensors in the Home-group will stay disabled. 7.5 Silent mode Press , followed by or . The alarm system will arm or disarm silently. The external siren will not give an alarm signal.
| ENGLISH without disturbing the other inhabitants. (The alarm system itself will confirm with a short sound signal) 7.6 Panic button Regardless the status of het alarm; armed or disarmed, by pressing the SOS button the alarm system will immediately enable the panic status. 7.7 Register a new remote control 1. Push the button on the back of the alarm system (Check if the LED status shown below is lid red). 2. Now you can register the new remote control by pressing a random button on the remote.
| ENGLISH 8.0 Install motion detector 8.1 front of motion detector 1. 2. 3. Detection window LED indicator Mounting bracket LED indicator: Flashes continuously: Motion detector is performing a self-test Flashes 1x: Motion detected Flashes 2x: Self-test completed. Motion detector is active Flashes once per 3 seconds: Battery power low, exchange battery* * You will receive a text message if battery level is low.
| ENGLISH 8.2.1 Infrared sensors The infrared sensors detect the motion. These sensors need to be clean at all time. Do no touch the sensors! 8.2.2 Anti sabotage button If the motion detector is opened this switch will detect it and trigger the alarm. 8.2.3 LED On/Off By switching this jumper setting you can set if the LED in front of the motion detector will be switched “On or Off”. By default this setting is turned ON (LED ON). 8.2.
| ENGLISH 8.3 Rear motion detector Test button 8.3.1 Test mode After the self-test has finished press the test button once. The motion detector will send a trigger signal (flashes 1x). 8.3.2 Activated If the motion sensor is triggered more than 2 times within 3 minutes the device switches automatically to power saving mode. The motion detector will activate again if it does not register motion for a time period of 3 minutes. 8.3.3 Pair the motion detector 1.
| ENGLISH Notice: During the registration process be sure no other sensor is triggered. If a motion detector is in the same room make sure you cover the motion detector or place the motion detector temporarily in a different room. 8.4 Installation tips Avoid installation of the motion detector in range of a window, air-conditioning, radiator, refrigerator, oven, direct sunlight or other places with high temperature fluctuation.
| ENGLISH Motion detectors are usually placed at 2 meters from the floor on the wall. First install the mounting bracket before placing the motion detector in the bracket. Point the detector in the direction you wish to secure. Test if the motion detector is working properly in test mode (see chapter 8.5).
| ENGLISH Side view Top view 8.5 Test the motion detector 1. After you fully installed the motion detector and the self-test is completed you can test the motion detector by walking within the range of the motion detector from one side to the other side. 2. The LED indicator of the motion detector will flash if motion is detected. 3. Adjust the motion sensor to get the best results. And repeat the test.
| ENGLISH 9.0 Install the Window/Door sensor 9.1 Front window/door sensor LED Indicator Magnet Sensor LED indicator: Flashes 1x: Window/Door is detected as open. Flashes quickly: Battery power low, exchange battery* * You will receive a text message if battery level is low. The message contains the following information (up to sensor 9) sensor name with additionally the text ‘battery almost empty’. From sensor 10 the name will be replaced for a zone nr.
| ENGLISH 9.2.1 Anti sabotage button If the sensor is opened this switch will detect it and trigger the alarm. 9.2.2 Group settings (jumpers) Every sensor can be configured to be added to a single group by setting the jumper settings; home-group, normal group or 24-hours group. Bellow you will see an overview of the meaning and how to configure the jumper settings for that type of zone. Remark: Determine before pairing with the alarm system in which group the sensor will be operational.
| ENGLISH The distance between the sensor and the magnet must not exceed 1cm. Mount both parts with the supplied double-sided tape. You can also choose to mount the sensor by using screws. It’s not recommended to install the sensor in a room with a lot of metal. Neither mount the sensor on constructions. Always check if the red LED will turn on when the door /window is opened. 9.3.1 Register the window/door sensor 1. Make sure the sensor and the magnet are located next to each other.
| ENGLISH 10.0 Technical specifications 10.
| ENGLISH 11.0 Frequently Asked Questions and other related information The latest frequently asked questions for your product can be found on the support page of your product. Eminent will update these pages frequently to assure you have the most recent information. Visit www.eminent-online.com for more information about your product. 12.0 Service and support This user’s manual has been carefully written by Eminent’s technical experts.
| ENGLISH Also, you will find frequently asked questions in the FAQ section. It is highly recommended to consult the FAQ section. Very often the answer to your questions will be found here. 14.0 Warranty conditions The five-year Eminent warranty applies to all Eminent products, unless mentioned otherwise before or during the moment of purchase. After buying a second-hand Eminent product the remaining period of warranty is measured from the moment of purchase by the product’s initial owner.
