User Guide

VOLUME
B122rH
VOLUME
B122rH
TONE
B124rH
TONE
B124rH
TONE
B124rH
VOLUME
B122rH
VOLUME
B122rH
RED
RED
RED
NECK PICKUP
BRIDGE PICKUP
BATTERY
NEG (-)
RED
RED
RED
GROUND
BRIDGE P/U
NECK P/U
OUTPUT
- 9V +
NK VOLUME
BR VOLUME
T
R
S
MASTER
TONE
OUTPUT CABLE
T
R
S
NK VOLUME
FROM NECK PICKUP
FROM BRIDGE PICKUP
BR VOLUME
BATTERY
NEG (-)
NK TONE
BR TONE
OUTPUT CABLE
- 9V +
GROUND
BRIDGE P/U
NECK P/U
OUTPUT
KFK INSTRUCTIONS Page 4
Diagram #8
2 Pickups
2 Volume (either volume will act as a master)
2 Tone
Toggle Style Switch
PA2
Diagram #7
2 Pickups
Toggle Style Switch
Volume each Pickup (Volumes are independent)
Master Tone and PA2
PA2
NOTE:
REVERSED
CONNECTOR
Refer to Diagram #7 Above:
1) Install the Pickups and route the pickup cables to the control cavity.
If the cables are too long, wind up any excess and keep it under the pickup.
2) Plug the neck and bridge pickup cables onto the volume controls as shown.
3) Plug a coax cable from the Bridge Volume to the Pickup Buss (Position 1).
Plug a coax cable from the Neck Volume to the Pickup Buss (Position 2).
Plug a coax cable from the Pickup Buss (Position 3) to the Master Tone.
4) Plug a coax cable from the Master Tone control to the input of the PA2.
Note the reversed connector.
5) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The BR Terminal is the Bridge Pickup, The NK Terminal is the Neck Pickup, the
output of the switch goes to the O terminal. Use the BLACK section of the
terminal block for any ground connections.
6) Plug the output cable from the PA2 to the output jack and and push the
connectors onto the T and S terminals of the jack.
7) Plug the Battery Negative wire (Black) onto the R terminal of the output jack.
8) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED wire of the PA2 and the RED wire of the battery clip.
9) Put the battery in the foam insulator provided and place it securely in the
control cavity. We suggest that you plug in the instrument and test it before
closing the control cavity.
Refer to Diagram #8 Below:
1) Install the Pickups and route the cables to the control cavity.
If the cables are too long, keep any excess under the pickup.
2) Plug the neck and bridge pickup cables onto the Volume controls as shown.
3) Plug a coax cable from each of the Volume controls to the tone controls.
4) Plug a coax cable from the Bridge Volume to the Pickup Buss (Position 1).
Plug a coax cable from the Neck Volume to the Pickup Buss (Position 2).
Plug a coax cable from the Pickup Buss (Position 3) to the input of the PA2.
Note the reversed connector on the PA2.
5) Strip the insulation from the switch wires and Insert them into the GREEN
and BLACK Terminal Blocks and tighten the screws with a small screwdriver.
The BR Terminal is the Bridge Pickup, The NK Terminal is the Neck Pickup, the
output of the switch goes to the O terminal. Use the BLACK section of the
terminal block for any ground connections.
6) Plug the output cable from the PA2 to the output jack and push the
connectors onto the T and S terminals of the jack.
7) Plug the Battery Negative wire (Black) onto the R terminal of the output jack.
8) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED wire of the PA2 and the RED wire of the battery clip.
9) Put the battery in the foam insulator provided and place it securely in the
control cavity. We suggest that you plug in the instrument and test it before
closing the control cavity.