User Guide

ManualsBrandsEMG ManualsElectric Guitar PartsEMG KHBB Kirk Hammett Bone Breaker Humbucker Guitar Pickup Set

PICKUP CABLE 15” (38cm)

OUTPUT CABLE 6” (15cm)

4 CONNECT CABLES 5.5” (14cm)

BATTERY CABLE 7” (18cm)

- 9V +

.390

(10)

(6)

(8)

.235

.310

INSTALLATION INFORMATION

EMG MODELS: EMG-KH BONE BREAKER SET

(EMG-BB BRIDGE/ EMG-BB NECK)

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.

BOX 4394

NTA ROSA, CA

402 USA

P (707) 525-9941

F (707) 575-7046

GPICKUPS.COM

0230-0341rA

*Note: Logo Colors are not distinguished on EMG Metal Works Pickups

**Note: Magnet Type: A (Alnico) A/S (Alnico/Steel) C (Ceramic) C/S (Ceramic/Steel)

Installation notes:

All EMG Pickups are compatible with each other. EMG accessories, the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System

without requiring an extra battery. DO NOT reconnect the bridge ground wire, EMG Pickups do not require string grounding. Use the 25K Ohm

controls that are included for best results. If your output jack is a long panel style you will need a stereo jack, use a SwitchCraft 152B , soldering

will be required (see the bottom of page 2). Adjust the pickup level to the strings, and at a distance that works for you, experiment. Alternate

wiring diagrams are available at; emgpickups.com.

SPECIFICATIONS: MODEL:

BB-N BB-B

Logo Color* Green Green

Magnet Type ** A C/S

Resonant Frequency (KHz) 1.80 1.63

Output Voltage (String) 3.00 3.00

Output Voltage (Strum) 4.50 4.50

Output Noise (60 Hz) -100 -100

Output Impedance (Kohm) 10 10

Current @9V (Microamps) 80 80

Battery Life (Hours) 3000 3000

Maximum Supply (Volts DC) 27 27

B245

2.75

1.50

3.09

3/48 MOUNTING HOLES

.900

.725

BATTERY

BUSS

2 PICKUP IN/ OUT

BATTERY BUSS

STEREO OUTPUT

JACK

2 VOLUME CONTROLS (25K)

2 TONE CONTROLS (25K)

(69.8)

(38.1)

(22.8)

(18.4)

(78.5)

ADJUSTMENT

SCREWS & SPRINGS (2 pr)

Included with each pickup SET:

Summary of content (4 pages)

PAGE 1
2.75 (69.8) 0230-0341rA 1.50 (38.1) PO BOX 4394 SANTA ROSA, CA 95402 USA 3.09 (78.5) 3/48 MOUNTING HOLES P (707) 525-9941 F (707) 575-7046 EMGPICKUPS.COM .900 (22.8) .725 (18.4) INSTALLATION INFORMATION EMG MODELS: EMG-KH BONE BREAKER SET (EMG-BB BRIDGE/ EMG-BB NECK) SPECIFICATIONS: MODEL: BB-N BB-B Logo Color* Green Green Magnet Type ** A C/S Resonant Frequency (KHz) 1.80 1.63 Output Voltage (String) 3.00 3.00 Output Voltage (Strum) 4.50 4.
PAGE 2
Installation Instructions: EMG Models: EMG-KH BB Set General Notes: Every attempt has been made to make this a solderless installation. There are some instances where this is not possible; 1) If your instrument uses the long panel output jack and you had passive pickups you will need a new stereo output jack, the Switchcraft 152B is recommended. Soldering to the new jack will be required, see diagram #6.
PAGE 3
2 Pickups / Toggle Select Switch / 2 Volumes and Master Tone Refer to Diagram #4 1) Install the Pickups and route the Pickup cables to the control cavity. If the cables are too long, wind up the excess and keep it under the pickup. 2) Mount the Volume and Tone controls into the body. Plug both pickup cables onto the Volume controls as shown.
PAGE 4
2 Pickups / Toggle Select Switch / 2 Volumes and 2 Tones) Refer to Diagram #5 1) Install the Pickups and route the cables to the control cavity. If the cables are too long, wind up the excess and keep it under the pickup. 2) Mount the Volume and Tone controls into the body Plug both Neck and Bridge pickup cables onto the Volume Controls as shown. Plug a coax cable from the Bridge (BR) Volume control to the Pickup Buss (Position 1).