User Guide

ManualsBrandsEMG ManualsOtherEMG ACB-5 Active 5-String Banjo Pickup

0230-0267A

PO BOX 4394

SANTA ROSA, CA

95402 USA

P (707) 525-9941

F (707) 575-7046

EMGPICKUPS.COM

The “Sweet” Spot

From both sound trials and experiments it’s been

determined that a distance of 3.750 inches (95mm)

is about the best spot for the pickup.

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.

TOOLS REQUIRED:

#1 PHILLIPS HEAD SCREW DRIVER

INCLUDED :

(2 ea.) CR2032 LITHIUM BATTERIES

9/64 ALLEN HEX WRENCH

General Operation

The EMG-ACB Banjo Pickup is the first of its kind to use 3 different pickup elements. First, the pickup is electro-magnetic so it senses the string

motion. Second, it has 3 acoustic chambers that allow sound waves inside the banjo to add a microphonic element to the sound. Third, it uses

a steel sensing element on the head of the banjo that can be positioned for additional tone. The EMG Banjo pickup is active and contains a high

quality preamp that features ultra-low noise and low current drain. The Pickup is powered by two Lithium Batteries (6 Volts). Everything needed

is included with the pickup, so the installation is simple, and above all, flexible.

Magnetic Output Level:

The output level of the pickup will depend on the placement along the coordinator rods. The output level of the pickup has been set to work at

the “Sweet Spot” shown below. If you slide the pickup closer towards the fingerboard the output will increase. If you wish, the pickup can be

spaced further away from the strings to set the output where you desire.

Acoustic (Microphonic) Level:

The amount of microphonic sensing can be controlled if you experience feedback when playing at high volume levels. The 3 acoustic chambers

surrounding the coils are .125 wide and can be filled with the “acoustic plugs” included. If you experience feedback, plugging the center slot

usually does the trick. Do not use foam, it’s not a solid enough material.

Banjo Head Steel Strip Level:

Included with the pickup is .002 thick strip of steel shim-stock, used by the pickup to “sense” the head of the banjo. It can be installed on

either the inside or the outside of the head. It has a pressure sensitive adhesive on one side for attachment to the head. It’s not necessary to

use the steel strip in order for the pickup to work, it is simply an addition to the sound of the instrument.

INSTALLATION INFORMATION

EMG MODEL: EMG-ACB BANJO PICKUP & VOLUME

SPECIFICATIONS: MODEL:

EMG-ACB

Logo Color Gold

Magnet Type Alnico

Resonant Frequency (KHz) 2.00

Output Voltage (String) *P.D.

Output Noise (60 Hz) -120

Output Impedance (Kohm) 2.00

Current @6V (Microamps) 340

Battery Life (Hours) 600

Maximum Supply (Volts DC) 18

*P.D. (Placement Dependent)

2.875

1.625

3.048

MOUNTING HOLES

.560

3.750

Summary of content (4 pages)

PAGE 1
2.875 0230-0267A 1.625 PO BOX 4394 SANTA ROSA, CA 95402 USA 3.048 MOUNTING HOLES P (707) 525-9941 F (707) 575-7046 EMGPICKUPS.COM .560 INSTALLATION INFORMATION EMG MODEL: EMG-ACB BANJO PICKUP & VOLUME General Operation The EMG-ACB Banjo Pickup is the first of its kind to use 3 different pickup elements. First, the pickup is electro-magnetic so it senses the string motion. Second, it has 3 acoustic chambers that allow sound waves inside the banjo to add a microphonic element to the sound.
PAGE 2
Installation Instructions: EMG Model: BANJO PICKUP 1) Attach the Rod Strap The ACB Pickup is supplied already mounted in the Pickup Bracket with the two phillips head screws fully tightened. They will be adjusted later. Using the 9/64 Hex wrench included, attach the Rod Strap to the pickup bracket as shown keeping the two hex screws somewhat loose. Be sure the 3 pin connector is in the position shown so the exposed magnetic poles will be under the lower G and D Strings.
PAGE 3
Installation Instructions: EMG Model: BANJO PICKUP 4) Battery Holder and Battery Installation Install the Battery Holder as shown on the rods and install two CR2032 batteries. Be sure the positive side of both batteries are facing the Battery Holder spring terminal. Positive of both batteries facing out 5) Output Jack/ Volume Installation Install the Output Jack assembly as shown below. Slide the threaded strip behind the lugs and tighten using the four screws provided.
PAGE 4
Installation Instructions: EMG Model: BANJO PICKUP 8) Adding the Steel Strip The steel strip included can be installed on either the inside or the outside of the head. It has a pressure sensitive adhesive on one side for attachment to the head. The adhesive is not strong, so the steel can be moved if desired. In order to work correctly, it should be installed in the direction shown in the diagrams.