Instruction manual

ManualsBrandsEmerson ManualsConsumer electronicsSolu Comp Xmt-P-FF/FI

FIGURE 4-23. CSA Intrinsically Safe Installation (1 of 2) for Model Xmt-P-FI

10/6/04

59.97

29.97

7.97

21.69

5.99

HAZARDOUS AREA

CLASS III

CLASS II, GRPS E-G

IS CLASS I, GRPS A-D

208.96mW

64.15mA

13.03V

Po;

Isc, It OR lo;

Voc, Vt OR Uo;

COMPONENT THAT DOES NOT DISSIPATE MORE THAN 1.3W.

AND THE NEC, ANSI/NFPA 70. THEY CAN NOT GENERATE NOR STORE MORE THAN 1.5V, 10

0mA, 25mW OR A PASSIVE

5. SENSORS WITHOUT PREAMPS SHALL MEET THE REQUIREMENTS OF SIMPLE APPARATUS AS DEFINED IN ANSI/

ISA RP12.6

OR SIMPLE APPARATUS

CSA APPROVED DEVICE

+PH SENSOR

J. FLOCK

CSA APPROVAL.

12. NO REVISION TO DRAWING WITHOUT PRIOR

TB1-1 THRU 12

MODEL XMT-P-FI

2. INTRINSICALLY SAFE APPARATUS (MODEL XMT-P-FI, MODEL 375)

GROUPS

GAS

OUTPUT PARAMETERS

(mH)

(uF)

TABLE I

0.9645

A, B

TABLE II

PARAMETERS

OUTPUT

3. PREAMPLIFIER TYPE 23546-00, 23538-00 OR 23561-00 MAY BE UTILIZED INSTEAD OF THE MODEL XMT-P-FI

MAY BE ALSO USED. THE OUTPUT PARAMETERS SPECIFIED IN TABLE II ARE VALID FOR EITHER PREAMPLIF

IER.

1. THE MODEL XMT-P-FI TRANSMITTER INCLUDES INTEGRAL PREAMPLIFIER CIRCUITRY. AN EXTERNAL PREAMPLIFIER

XMTR

XMT-

P-FI

MODEL

XMT-P-FI

XMT-P-FF ENTITY PARAMETERS

0.0

SUPPLY / SIGNAL TERMI

NALS TB2-1, 2 AND 3

321

23456 7 8 9 10 11 121

SPECIFIED IN TABLE I

THE CAPACITANCE AND INDUCTANCE OF THE LOAD CONNECTED TO THE SENSOR TERMINALS MUST NOT EXCEED THE VALUES

La Li (SENSOR) + Lcable.

WHERE Ca Ci (SENSOR) + Ccable;

23546-00 REMOTE PREAMPLIFIER.

TRANSMITTER INTEGRAL PREAMPLIFIER CIRCUITRY. A WEATHER RESISTANT ENCLOSURE MUST HOUSE THE TYPE

(SEE NOTE 8)

SAFETY BARRIER

Li+ Lcable.

Ci+ Ccable;

Pmax OR Pi

Imax OR Ii

Vmax OR Ui

FIELD DEVICE INPUT ASSOCIATED APP

ARATUS OUTPUT

WITH ASSOCIATED APPARATUS WHEN THE FOLLOWING IS TRUE:

8. THE INTRINSICALLY SAFE ENTITY CONCEPT ALLOWS INTERCONNECTION OF INTRINSICALLY SAFE DEVICES

380

17.5

La, Lt OR Lo

Ca, Ct OR Co

SYSTEMS FOR HAZARDOUS (CLASSIFIED) LOCATIONS" AND THE CANADIAN ELECTRICAL CODE, CSA C22.1, PART 1, APPENDIX F.

4. INSTALLATION SHOULD BE IN ACCORDANCE WITH ANSI/ISA RP12.06.01 "INSTALLATION OF INTRINSICALLY SAFE

0.4

TABLE III

MODEL NO.

5.32

Vmax (Vdc) Li (mH)

Ci (nF)

Pmax (W)

Imax (mA)

0.0

1.9

ENTITY PARAMETERS: REMOTE TRANSMITTER INTERFACE

Isc max OUT:uA

Voc max OUT: Vdc

Pmax IN: W

Imax IN:mA

Vmax IN: Vdc

375

MODEL NO.

1.0

20030

Li (mH)

Ci (uF)

WHEN INSTALLING THIS EQUIPMENT.

9 . ASSOCIATED APPARATUS MANUFACTURER'S INSTALLATION DRAWING MUST BE FOLLOWED

FIELD COMMUNICATOR

ROSEMOUNT MODEL 375

TABLE III)

(SEE NOTE 2 AND

CLASS I AREA ONLY

INTERFACE FOR USE IN

REMOTE TRANSMITTER

SUITABILITY FOR DIVISION 2.

SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY OR

DISCONNECT POW ER BEFORE SERVICING.

TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOS

PHERES,

WARNING-

INDUCTANCE (La) WHICH CAN BE SAFELY CONNECTED TO THE APPARATUS. (REF. TABLES I, II AND III).

INCLUDING INTERCONNECTING WIRING, MUST BE EQUAL OR LES

S THAN THE CAPACITANCE (Ca) AND

UNPROTECTED CAPACITANCE (Ci) AND INDUCTANCE (Li) OF THE INTRINSICALLY SAFE APPARATUS,

DELIVERED BY THE AS

SOCIATED APPARATUS (SAFETY BARRIER). IN ADDITION, THE MAXIMUM

EQUAL TO OR GREATER THAN THE VOLTAGE (Voc OR Vt) AND CURRENT (Isc OR It) WHICH CAN BE

THE VOLTAGE (Vmax) AND CURRENT (Imax) OF THE INTRINSICALLY SAFE APPARATUS MUST BE

AND ASSOCIATED APPARATUS (SAFETY BARRIER) SHALL MEET THE FOL

LOWING REQUIREMENTS:

17.5 VDC MAX

POWER SUPPLY

UNSPECIFIED

11. THE ASSOCIATED APPARATUS MUST BE CSA APPROVED.

7. RESISTANCE BETWEEN INTRINSICALLY SAFE GROUND AND EARTH GROUND MUST BE LE

SS THAN 1.0 Ohm.

6. DUST-TIGHT CONDUIT SEAL MUST BE USED WHEN INSTALL

ED IN CLASS II AND CLASS III ENVIRONMENTS.

WARNING-

NON-HAZARDOUS AREA

LOAD

MORE THAN 250 Vrms OR Vdc.

10. CONTROL EQUIPMENT CONNECTED TO ASSOCIATED APPARATUS MUST NOT USE OR GENERATE

THIS DOCUMENT IS

CERTIFIED BY

REV

REVISIONS NOT PERMITTED

W/O AGENCY APPROVAL

(CSA)

MOD XMT-P-FI XMTR

B. JOHNSON

SCHEMATIC, INSTALLATION

Uniloc

9/15/04

NOMINAL SURFACE FINISH 125

A9047

10-6-04

1400304

SHEET OF

NONE

J. FLOCK

1400304

10-96

APPROVALS

.030

.XX

.XXX

.010

ANGLES

1/2

TOLERANCES

SOLID EDGE

CHK

REVISION

DATE

BYDESCRIPTION

ECO

LTR

NOTES: UNLESS OTHERWISE SPECIFIED

REVECO NO.

RELEASE DATE

PART NO.

ITEM

QTY

BILL OF MATERIAL

DESCRIPTION

DATE

THIS DWG CONVERTED TO

DRAWN

CHECKED

to those who may compete with Rosemount Analytical.

Rosemount Analytical, and is not to be made available

This document contains information proprietary to

TYPE

SCALE

TITLE

REV

DWG NO.

SIZE

ENGR APVD

PROJECT

MATERIAL

FINISH

MACHINED FILLET RADII .020 MAX

REMOVE BURRS & SHARP EDGES .020 MAX

DIMENSIONS ARE IN INCHES

UNLESS OTHERWISE SPECIFIED

Rosemount Analytical,

Uniloc Division

2400 Barranca Pkwy

Irvine, CA 92606

CSA