Instruction manual

ManualsBrandsEmerson ManualsConsumer electronicsSolu Comp Xmt-P-FF/FI

FIGURE 4-20. FM Intrinsically Safe Installation (1 of 2) for Model Xmt-P-FI

10/6/04

10/6/04 10/6/04

14. METAL CONDUIT IS NOT REQUIRED BUT IF USED BONDING

BETWEEN CONDUIT IS NOT AUTOMATIC AND MUST BE

PROVIDED AS PART OF THE INSTALLATION.

Isc, It OR Io;

Voc, Vt OR Uo;

Po;

COMPONENT THAT DOES NOT DISSIPATE MORE THAN 1.3W.

AND THE NEC, ANSI/NFPA 70. THEY CAN NOT GENERATE NOR STORE MORE THAN 1.5V, 100mA, 25mW OR A PASSIVE

6. SENSORS WITHOUT PREAMPS SHALL MEET THE REQUIREM

ENTS OF SIMPLE APPARATUS AS DEFINED IN ANSI/ISA RP12.6

OR SIMPLE APPARATUS

FM APPROVED DEVICE

+PH SENSOR

3. INTRINSICALLY SAFE APPARATUS (MODEL XMT-P-FI, MODEL 375)

Pmax NOT GREATER THAN 0.9 W

Isc OR It NOT GREATER THAN 200 mA

Voc OR Vt NOT GREATER THAN 30 V

SUPPLY/SIGNAL TERMINALS TB2-1, 2 AND 3.

1. ANY SINGLE SHUNT ZENER DIODE SAFETY BARRIER APPRO

VED BY FM HAVING THE FOLLOWING OUTPUT PARAMETERS:

4. PREAMPLIFIER TYPE 23546-00, 23538-00 OR 23561-00 MAY BE UTILIZED INSTEAD OF THE MODEL XMT-P-FI

MAY BE ALS

O USED. THE OUTPUT PARAMETERS SPECIFIED IN TABLE II ARE VALID FOR EITHER PREAMPLIFIER.

2. THE MODEL XMT-P-FI TRANSMIT

TER INCLUDES INTEGRAL PREAMPLIFIER CIRCUITRY. AN EXTERNAL PREAMPLIFIER

XMTR

XMT-P-FI

MODEL

XMT-P-FI

XMT-P-FI ENTITY PARAMETERS

(FM APPROVALS)

MOD XMT-P-FI XMTR

0.0

SUPPLY / SIGNAL TERMINALS TB2-1, 2 AND 3

3 2 1

2 3 456 78 9 10 11 121

SPECIFIED IN TABLE I

THE CAPACITANCE AND INDUCTANCE OF THE LOAD CONNECTED TO THE SENSOR TERMINALS MUST NOT EXCEED THE VALUES

La Li (SENSOR) + Lcable.

WHERE Ca Ci (SENSOR) + Ccable;

23546-00 REMOTE PREAMPLIFIER.

TRANSMITTER INTEGRAL PREAMPLIFIER CIRCUITRY. A WEATHER RESISTANT ENCLOSURE MUST HOUSE THE TYP

(SEE NOTES 1 & 9)

SAFETY BARRIER

Li+ Lcable.

Ci+ Ccable;

Pmax OR Pi

Imax OR Ii

Vmax OR Ui

FIELD DEVICE INPUT ASSOCIATED APPARATUS OUTPUT

WITH ASSOCIATED APPARATUS WHEN THE FOLLOWING IS TRUE:

9. THE INTRINSICALLY SAFE ENTITY CONCEPT ALLOWS INTERCONNECTION OF INTRINSICALL

Y SAFE DEVICES

380

17.5

La, Lt OR Lo

Ca, Ct OR Co

SYSTEMS FOR HAZARDOUS (CLASSIFIED) LOCATIONS" AND THE NATIONAL ELECTRICAL CODE (ANSI/NFPA 70) SECTIONS 504 AND 505.

5. INSTALLATION SHOULD BE IN ACCORDANCE WITH ANSI/ISA RP12.06.01 "INSTALLATION OF INTRINSICALL

Y SAFE

0.4

TABLE III

MODEL NO.

5.32

Vmax (Vdc)Li (mH)

Ci (nF)

Pmax (W)

Imax (mA)

0.0

321.9

ENTITY PARAMETERS: REMOTE TRANSMITTER INTERFACE

Isc max OUT:uA

Voc max OUT: Vdc

Pamx IN: W

Imax IN:mA

Vmax IN: Vdc

375

MODEL NO.

1.0

20030

Li (mH)

Ci (uF)

WHEN INSTALLING THIS EQUIPMENT.

10. ASSOCIATED APPARATUS MANUFACTURER'S INSTALLATION DRAWING MUST BE FOLLOWED

FM APPROVAL.

13. NO REVISION TO DRAWING WITHOUT PRIOR

FIELD COMMUNICATOR

ROSEMOUNT MODEL 375

TABLE III)

(SEE NOTE 3 AND

CLASS I AREA ONLY

INTERFACE FOR USE IN

REMOTE TRANSMITTER

SUITABILITY FOR DIVISION 2.

SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY OR

DISCONNECT POWER BEFORE SERVICING.

TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOS

PHERES,

GROUPS A, B, C, D, E, F, G;

DIVISION 1,

IS CLASS I, II, III,

HAZARDOUS AREA

WARNING-

INDUCTANCE (La) WHICH CAN BE SAFELY CONNECTED TO THE APPARATUS. (REF. TABLES I, II AND III).

INCLUDING INTERCONNECTING WIRING, MUST BE EQUAL OR LE

SS THAN THE CAPACITANCE (Ca) AND

UNPROTECTED CAPACITANCE (Ci) AND INDUCTANCE (Li) OF THE INTRINSICALLY SAFE APPARATUS,

DELIVERED BY THE ASSOCIATED APPARATUS (SAFETY BARRIER). IN ADDITION, THE MAXIMUM

EQUAL TO OR GREATER THAN THE VOLTAGE (Voc OR Vt) AND CURRENT (Isc OR It) WHICH CAN BE

THE VOLTAGE (Vmax) AND CURRENT (Imax) OF THE INTRINSICALLY SAFE APPARATUS MUST BE

AND ASSOCIATED APPARATUS (SAFETY BARRIER) SHALL ME

ET THE FOLLOWING REQUIREMENTS:

17.5 VDC MAX

POWER SUPP LY

UNSPECIFIED

12. THE ASSOCIATED APPARATUS MUST BE FM APPROVED.

8. RESISTANCE BETW

EEN INTRINSICALLY SAFE GROUND AND EARTH GROUND MUST BE LESS THAN 1.0 Ohm.

7. DUST-TIGHT CONDUIT SEAL MUST BE USED WHEN INSTALLED IN CLASS II

AND CLASS III ENVIRONMENTS.

WARNING-

NON-HAZARDOUS AREA

LOAD

MORE THAN 250 Vrms OR Vdc.

11. CONTROL EQUIPMENT CONNECTED TO ASSOCIATED APPARATUS MUST NOT USE OR GENERATE

J. FLO CK

B. JOHNSON

THIS DOCUMENT IS

CERTIFIED BY

REV

REVISIONS NOT PERMITTED

W/O AGEN CY APPROVAL

SCHEMATIC, INSTALLATION

Uniloc

9/15/04

NOMINAL SURFACE FINISH 125

9064

10-6-04

1400300

SHEET OF

NONE

J. FLO CK

1400300

10-96

APPROVALS

.030

.XX

.XXX

.010

ANGLES

1/2

TOLERANCES

SOLID EDGE

CHK

REVISION

DATE

BYDESCRIPTION

ECO

LTR

NOTES: UNLESS OTHERWISE SPECIFIED

REVECO NO.

RELEASE DATE

PART NO.

ITEM

QTY

BILL OF MATERIAL

DESCRIPTION

DATE

THIS DWG CONVERTED TO

DRAWN

CHECKED

to those who may compete with Rosemount Analytical.

Rosemount Analytical, and is not to be made available

This document contains information proprietary to

TYPE

SCALE

TITLE

REV

DWG NO.

SIZE

ENGR APVD

PROJECT

MATERIAL

FINISH

MACHINED FILLET RADII .020 MAX

REMOVE BURRS & SHARP EDGES .020 MAX

DIMENSIONS ARE I N INCHES

UNLESS OTHERWISE SPECIFIED

Rosemount Analytical,

Uniloc Division

2400 Barranca Pkwy

Irvine , CA 92606

21.69

5.99

0.9645

29.97

7.97

64.15mA

13.03V

208.96mW

TB1-1 THRU 12

MODEL XMT-P-FI

GROUPS

GAS

OUTPUT PARAMETERS

(mH)

(uF)

TABLE I

59.97

A, B

TABLE II

PARAMETERS

OUTPUT

FM A