Switch User Manual
Table Of Contents
- Contents
- 1 Safety Information
- 2 Introduction
- 3 Mechanical Installation
- 4 Electrical Installation
- 5 Getting Started
- 6 Protocols
- 7 Drive profile (DSP-402) support
- 7.1 0x6040 Controlword
- 7.2 0x6041 Statusword
- 7.3 Common profile features
- 7.3.1 Sequencing control
- 7.3.2 0x605A Quick stop option code
- 7.3.3 0x605B Shutdown_option_code
- 7.3.4 0x605C Disable_operation_option_code
- 7.3.5 0x605E Fault_reaction_option_code
- 7.3.6 0x6060 Modes_of_operation
- 7.3.7 0x6061 Modes_of_operation_display
- 7.3.8 0x6085 Quick_stop_deceleration
- 7.3.9 Profile units
- 7.3.10 0x608F Position_encoder_resolution
- 7.3.11 0x6091 Gear_ratio
- 7.3.12 0x6092 Feed_constant
- 7.3.13 Basic position control
- 7.3.14 0x6062 Position_demand_value
- 7.3.15 0x6064 Position_actual_value
- 7.3.16 0x60F4 Following_error_actual_value
- 7.3.17 0x60FB Position_control_parameter_set object
- 7.4 Interpolated position mode
- 7.5 vl velocity mode
- 7.5.1 0x6042 vl_target_velocity
- 7.5.2 0x6043 vl_velocity_demand
- 7.5.3 0x6044 vl_velocity_actual_value
- 7.5.4 0x6046 vl_velocity_min_max_amount
- 7.5.5 0x6047 vl_velocity_min_max
- 7.5.6 0x6048 vl_velocity_acceleration
- 7.5.7 0x6049 vl_velocity_deceleration
- 7.5.8 0x604A vl_velocity_quick_stop
- 7.5.9 0x604B vl_setpoint_factor
- 7.5.10 0x604C vl_dimension_factor
- 7.6 Profile Torque mode
- 7.7 Homing Mode
- 8 Advanced features
- 9 Diagnostics
- 9.1 Module identification parameters
- 9.2 Network configuration objects
- 9.3 Diagnostic parameters
- 9.4 Drive trip display codes
- 9.5 SM-EtherCAT module temperature
- 9.6 SM-EtherCAT serial number
- 9.7 SM-EtherCAT error codes
- 9.8 Critical task % free
- 9.9 Worst case critical task % free
- 9.10 FLASH file system % free
- 9.11 Updating SM-EtherCAT firmware
- 10 Quick Reference
- 11 Glossary Of Terms
- Index

SM-EtherCAT User Guide 3
Issue Number: 2 www.controltechniques.com
Contents
1 Safety Information ..........................................................5
1.1 Warnings, cautions and notes ......................................................................5
1.2 Electrical safety - general warning ...............................................................5
1.3 System design and safety of personnel ....................................................... 5
1.4 Environmental limits .....................................................................................6
1.5 Compliance with regulations ........................................................................6
1.6 Motor ............................................................................................................6
1.7 Adjusting parameters ...................................................................................6
1.8 General safety considerations for remote operation ....................................7
2 Introduction ....................................................................8
2.1 Features .......................................................................................................8
2.2 Introduction to SM-EtherCAT ....................................................................... 8
2.3 What is EtherCAT? ......................................................................................8
2.4 Solution module identification ......................................................................8
2.5 Conventions used in this guide ....................................................................9
3 Mechanical Installation ................................................10
3.1 General Installation ....................................................................................10
4 Electrical Installation ...................................................11
4.1 SM-EtherCAT module information .............................................................11
4.2 Module grounding ......................................................................................11
4.3 Network topology ....................................................................................... 12
4.4 Minimum node-to-node cable length ..........................................................12
5 Getting Started .............................................................13
5.1 Quick start guide ........................................................................................13
5.2 Quick start flowchart ..................................................................................17
5.3 Saving parameters to the drive ..................................................................18
5.4 Re-initialising the SM-EtherCAT ................................................................18
5.5 Re-initialise all Solutions Modules ............................................................. 18
6 Protocols .......................................................................19
6.1 CANopen over EtherCAT (CoE) ................................................................19
7 Drive profile (DSP-402) support ..................................28
7.1 0x6040 Controlword ................................................................................... 28
7.2 0x6041 Statusword .................................................................................... 29
7.3 Common profile features ............................................................................29
7.4 Interpolated position mode .........................................................................39
7.5 vl velocity mode .........................................................................................41
7.6 Profile Torque mode ..................................................................................46
7.7 Homing Mode ............................................................................................. 47
8 Advanced features .......................................................55
8.1 Distributed clocks ....................................................................................... 55
8.2 SM-EtherCAT protocol support ..................................................................55