RTM-ATCA-7350 Installation and Use 6806800H30F February 2010
© 2010 Emerson All rights reserved. Trademarks Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. © 2010 Emerson Electric Co. All other trademarks are the property of their respective owners. Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.1 1.2 1.3 1.4 2 Overview of RTM-ATCA-7350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical Data . . . . . . . . . . . . . . . . .
Contents 2.8.3 3 Controls, LEDs and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 3.1 3.2 3.3 4 37 38 38 40 40 43 43 44 45 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Daughter Cards . . . . . . . . . .
List of Tables Table 1-1 Table 1-2 Table 1-3 Table 1-4 Table 2-1 Table 2-2 Table 3-1 Table 3-2 Table 3-3 Table 3-4 Table 3-5 Table 3-6 Table 4-1 Table 4-2 Table A-1 Table A-2 Mechanical Specifications of RTM-ATCA-7350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 6 RTM-ATCA-7350 Installation and Use (6806800H30F)
List of Figures Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 4-1 Figure 4-2 Figure 4-3 Wearing the ESD-Preventive Wrist Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the Filler Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Structure of RTM-ATCA-7350 . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Figures 8 RTM-ATCA-7350 Installation and Use (6806800H30F)
About this Manual Overview of Contents This manual is intended for the users who install and configure the RTM-ATCA-7350 of the server blade. The user must be a professional engineer in the server device field, who has been trained and is able to identify danger levels when operating the device. This manual describes the structure, appearance, functions, technical specifications, precautions, and installation procedure of the RTM-ATCA-7350.
About this Manual Abbreviation Definition FCC Federal Communications Commission FRU Field Replaceable Unit GE Gigabit Ethernet IEC International Electrotechnical Commission IPMB Intelligent Platform Management BUS IPMC Intelligent Platform Management Controller IPMI Intelligent Platform Management Interface KVM Keyboard, Video, and Mouse OOS Out of Service PCI Peripheral Component Interconnect RTM Rear Transition Module SCSI Small Computer System Window SDR Sensor Data Record SE
About this Manual Notation Description ... Repeated item for example node 1, node 2, ..., node 12 . Omission of information from example/command that is not necessary at the time being . . .. Ranges, for example: 0..
About this Manual Comments and Suggestions We welcome and appreciate your comments on our documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to us by filling out the following online form: http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form In "Area of Interest" select "Technical Documentation". Be sure to include the title, part number, and revision of the manual and tell us how you used it.
Introduction 1.1 1 Overview of RTM-ATCA-7350 The ATCA-7350 Rear Transition Module (RTM) of the server blade (hereinafter referred to as RTM-ATCA-7350) must work with the server blade ATCA-7350. RTM-ATCA-7350 provides external interfaces for the connected server blade. RTM-ATCA-7350 provides the following functions: z RTM-ATCA-7350 provides two daughter card connectors.
Introduction 1.3 Standard Compliances Standard Compliances The product is designed to meet the following standards. Table 1-2 Standard Compliances Standard Description UL 60950-1 Legal safety requirements EN 60950-1 IEC 60950-1 CAN/CSA C22.
Board Accessories Introduction Table 1-3 Product Nomenclature (continued) 1.4.2 Order Number Description RTM-ATCA-7350-2GE RTM FOR THE ATCA-7350 BLADE WITH 4 GE INTERFACES (ROHS 5/6) RTM-ATCA-7350-FC RTM FOR THE ATCA-7350 BLADE WITH 2 FC INTERFACES (ROHS 5/6) Board Accessories As of the printing date of this manual, the following board accessories were available.
Introduction 16 Board Accessories RTM-ATCA-7350 Installation and Use (6806800H30F)
Hardware Preparation and Installation 2.1 2 Overview This chapter describes: 2.2 z Unpacking and inspecting RTM-ATCA-7350 z Precautions during the operation z Preparations before installation z Installation procedure z Installing and replacing daughter cards z Connection of external cables z Removal procedure Unpacking and Inspecting RTM-ATCA-7350 Damage of Circuits Electrostatic discharge and incorrect installation and removal of the product can damage circuits or shorten their life.
Hardware Preparation and Installation Environmental and Power Requirements 3. Remove the desiccant bag shipped together with the blade and dispose of it according to your country’s legislation. The product is thoroughly inspected before shipment. If any damage occurred during transportation or any items are missing, please contact our customer's service immediately. 2.3 Environmental and Power Requirements The following environmental and power requirements are applicable to the board. 2.3.
Power Requirements Hardware Preparation and Installation Table 2-1 Environmental Requirements (continued) Requirement Operating Non-Operating Free Fall 1,200 mm (Packaged) /all edges and corners 1.0m (Packaged) per ETSI 300 019-2-2 (Blade level packaging) 25mm (unpackaged) per GR-63-CORE 2.3.2 Power Requirements Table 2-2 Power Requirements 2.4 Requirement Operating Power supply Provided by the server blade Maximum power consumption 14.
Hardware Preparation and Installation Ejector Handles Module Damage If the blade is not fully aligned with the interface in the backplane, too much force may twist the pins on the blade or backplane. Do not exert too much force when you insert the blade. Note the following points at the time of installing RTM-ATCA-7350: 2.4.1 z Make sure that you wear an electrostatic discharge (ESD)-preventive wrist strap to prevent the static electricity from hurting you or damaging the device.
Installation Preparations 2.5 Hardware Preparation and Installation z Install the device at once after you take it out of the antistatic package. If you need to lay down the device, place it back in the antistatic package. Do not lay the device on the shelf or cabinet. z Monitor the temperature and humidity of the equipment room. Warm air decreases the humidity and increases the static electricity in the room. Installation Preparations The installation preparations process includes: 2.5.
Hardware Preparation and Installation Wearing the ESD-Preventive Wrist Strap To wear the ESD-preventive wrist strap, proceed as follows: 1. Wrap the ESD-preventive wrist strap around your wrist, as shown in the figure below. 2. Fasten the latch. Make sure that the ESD-preventive wrist strap well touches your bare wrist. 3. Insert the grounding terminal of the ESD-preventive wrist strap in the jack of the cabinet or shelf.
Removing Filler Blades 2.5.2 Hardware Preparation and Installation Removing Filler Blades After a filler blade is removed, place it in the equipment room or other moisture-proof and dust-proof places. You should install a blank filler blade in the slot after removing the blade. Otherwise, it may effect the ventilation, heat dissipation, electromagnetic shielding and dust prevention of the shelf.
Hardware Preparation and Installation Installing and Replacing Daughter Cards 2.6 Installing and Replacing Daughter Cards 2.6.1 Precautions Incorrect installation or removal of additional devices or modules may damage the product or the additional devices or modules. Before installing or removing additional devices or modules, read the respective documentation. Personal Injury Power and communication cables Touching power and communication cables that are energized may cause injuries.
Preparations 2.6.2 Hardware Preparation and Installation z Ensure that your sleeves are tightened or rolled up above the elbow. For safety purpose, it is not recommended to wear jewelry, watch, glasses with metal frame, or clothes with metal buttons. z Do not exert too much force, or insert or remove the components forcibly. Avoid damage to the components or plug-ins, for example, the pins are bent or get short circuit.
Hardware Preparation and Installation 2.6.3.1 GE Daughter Card Installation Positions When the GE daughter card is used with the RTM-ATCA-7350 it can be installed on the daughter card connector J1, J2. The default position as used on the RTM-ATCA-7350-GE is position J2. Figure 2-3 2.6.3.2 Structure of RTM-ATCA-7350 1 J2 2 J1 Installing the GE Daughter Card To install the GE daughter card, proceed as follows. 1. Wear the ESD-preventive wrist strap.
GE Daughter Card Hardware Preparation and Installation 3. As shown in step 1 of the figure below, insert two plastic supports vertically in the holes used to fasten the GE daughter card. 4. As shown in step 2 of the figure below, at the back side of RTM-ATCA-7350, use a screwdriver to clockwise fasten the two screws used to fix the plastic supports. 5. Take the GE daughter card out of the antistatic package. 6.
Hardware Preparation and Installation FC Daughter Card After installation, check if RTM-ATCA-7350 can be powered on and work normally. Use the network cable to connect RTM-ATCA-7350 to the external network. Check if the network is connected properly and monitor whether the network port indicator is normal. 2.6.3.3 Replacing the GE Daughter Card To replace the GE daughter card, proceed as follows. 1. Wear the ESD-preventive wrist strap.
FC Daughter Card 2.6.4.2 Hardware Preparation and Installation Installing the FC Daughter Card To install the FC daughter card, proceed as follows. 1. Wear the ESD-preventive wrist strap. For more information refer, Wearing the ESDPreventive Wrist Strap on page 21. 2. Lay RTM-ATCA-7350 where the FC daughter card is to be installed on the antistatic desktop. 3. Insert two plastic supports vertically in the holes used to fasten the FC daughter card. 4.
Hardware Preparation and Installation Installing and Removing the RTM-ATCA-7350 5. Place the removed FC daughter card in an antistatic package. 6. Take the new FC daughter card out of the antistatic package. 7. Insert the FC daughter card in RTM-ATCA-7350 by facing the daughter card at an angle of 45° to the RTM. Align the daughter card connector with the connector on RTM-ATCA-7350, and the daughter card positioning holes with the plastic supports on RTM-ATCA-7350.
Installing RTM-ATCA-7350 Hardware Preparation and Installation The blue LED blinks indicating that the shelf manager is informed about the desire of the blade to power down the payload of the front blade and the power-down process is ongoing. 3. Wait until the blue LED of the front blade is permanently ON. A permanently switched ON LED indicates that the payload of the front blade has been powered down. 4. Remove the front blade. For instructions on how to remove the blade, refer to Section 2.7.2.
Hardware Preparation and Installation Removing RTM-ATCA-7350 10.Insert the main blade. For instructions on how to install the main blade, refer to Section 2.7.1.1 Installing the ATCA-7350 in a Powered Shelf in ATCA-7350 Installation and Use manual. 11.Close the handles of the front blades. The LEDs; OOS LED, Blue LED, and healthy LED of RTM are on. 12.Wait until the blue LED on the RTM is OFF. A switched off blue LED indicates that the payload of the RTM has become active. 2.7.
Connecting External Cables Hardware Preparation and Installation 6. As shown in step 3 of the figure below, remove RTM-ATCA-7350 along the guide rails. 7. Place RTM-ATCA-7350 in the antistatic package. Figure 2-6 Removing RTM-ATCA-7350 2 1 3 1 2 2.8 Connecting External Cables After RTM-ATCA-7350 is installed in the shelf, you can connect the keyboard, video, and mouse (KVM) cables.
Hardware Preparation and Installation Connecting KVM Cables Cable Damage 2.8.1 z There is a back cable trough at the back side of the shelf. You need to arrange and identify all cables and then bind and fasten them in the back cable through after connecting them. z If you use excessive force when installing cables, the cables may be damaged. z Do not exert too much force when you insert or remove the cables. Do not twist or tear the cables in any condition.
Connecting Network Cables 2.8.2 Hardware Preparation and Installation Connecting Network Cables Electromagnetic Radiation Make sure that the cable and connectors of the network cable are with shielding function and that both ends of the shielded layer of the network cable are grounded. It is recommended that the network cable is grounded through the metal cover of the network port connector.
Hardware Preparation and Installation 2.8.3 Connecting Optical Fibers Connecting Optical Fibers When RTM-ATCA-7350 is configured with the FC daughter card, it provides two external 2G FC interfaces. Optical fibers are used to connect RTM-ATCA-7350 to the external Storage Area Network (SAN) storage system. Optical modules for the FC daughter cards must be obtained separately. Recommended modules are FINISAR FTRJ8519P1BNL-HW, FINISAR FTRJ8519P2BNL-HW.
Controls, LEDs and Connectors 3.
Controls, LEDs and Connectors 3.2 Face Plate Connectors and LEDs Face Plate Connectors and LEDs The following figure shows the face plate of RTM-ATCA-7350 without daughter cards installed. Figure 3-1 Face Plate of RTM-ATCA-7350 Captive screw Ejector handle USB interface VGA interface OOS indicator IS indicator ATN indicator Filler panel H/S indicator Filler panel You need to install a filler blade in the position that is not occupied by the face plate of the daughter card. 3.2.
LEDs Controls, LEDs and Connectors The GE daughter card provides the network port indicators and the FC daughter card provides the FC status indicators. You can monitor these indicators to diagnose the current status of RTM-ATCA-7350. The following table lists the indicators on the RTM-ATCA-7350 face plate.
Controls, LEDs and Connectors 3.2.2 Connectors Connectors RTM-ATCA-7350 provides two daughter card connectors, as shown in the following figure. Figure 3-2 Structure of RTM-ATCA-7350 1 J2 2 J1 In the above figure: 3.2.2.
Connectors Controls, LEDs and Connectors z OOS indicator z IS indicator z ATN indicator z H/S indicator Figure 3-3 Connectors and Indicators of RTM-ATCA-7350 Captive screw USB interface VGA interface Ejector handle OOS indicator IS indicator ATN indicator Filler panel H/S indicator Filler panel RTM-ATCA-7350 Installation and Use (6806800H30F) 41
Controls, LEDs and Connectors 3.2.2.1.1 Connectors USB Port RTM-ATCA-7350 provides a single port USB connector on the face plate. The USB port is compliant to the USB 1.1 specification. The following USB Port Pin Assignment table describes the pinout information. Figure 3-4 RTM-ATCA-7350 Front Plate USB Connector Pinout Table 3-2 USB Port Pin Assignment 3.2.2.1.2 Pin Pin Name Description 1 +5V +5V Power Supply, Max 500mA each port. 2 Data- Differential Data transmitting pair.
Zone 3 Connectors Controls, LEDs and Connectors Table 3-3 VGA Port Pin Assignment 3.3 Pin Pin Name Description 1 RED Analog red video output signal. 2 GREEN Analog green video output signal. 3 BLUE Analog blue video output signal. 4 RESERVED1 Reserved. 5 RESERVED2 Reserved on RTM-ATCA-7350. 6 GROUND1 Connected to the logic ground of RTM-ATCA-7350. 7 GROUND2 Connected to the logic ground of RTM-ATCA-7350. 8 RESERVED3 Reserved on RTM-ATCA-7350.
Controls, LEDs and Connectors P31 Pinout RTM_EN0_ and RTM_EN_ are signals that indicate the RTM is firmly inserted. Table 3-4 PIN 30 Pinout 3.3.
P32 Pinout Controls, LEDs and Connectors Table 3-5 PIN 31 Pinout (continued) 3.3.3 ZD1 A B C D 8 RTM_EXP7_R XP2 RTM_EXP7_RXN 2 GND MCH_EXP7_R XP1 MCH_EXP7_RX N1 GND 9 RTM_EXP7_R XP1 RTM_EXP7_RXN 1 GND MCH_EXP7_R XP0 MCH_EXP7_RX N0 GND 10 RTM_EXP7_R XP0 RTM_EXP7_RXN 0 GND RTM_PCIE7_ CLK_P RTM_PCIE7_CL K_N GND P32 Pinout P32 is used for port1 and port4 signals of the Fabric interface, and the PCIE signals from front board.
Controls, LEDs and Connectors P32 Pinout Table 3-6 PIN 32 Pinout (continued) ZD2 A B 10 RTM_F C2_RX 3_H RTM_F C2_RX 3_L 46 GN D C D RTM_F C1_RX 3_H RTM_F C1_RX 3_L GN D E F RTM_F C2_RX 0_H RTM_F C2_RX 0_L GN D G H RTM_F C1_RX 0_H RTM_F C1_RX 0_L GN D RTM-ATCA-7350 Installation and Use (6806800H30F)
Functional Description 4.1 4 Overview This chapter describes: 4.2 z Block diagram z Daughter cards Block Diagram The following block diagram shows the main components of RTM-ATCA-7350 and how they interact/are connected. Figure 4-1 Block Diagram of RTM-ATCA-7350 EEPROM (SDR & FRU) LM80 Zone3(P30&P31&P32) IIC 5VSBY & 12V & 3.3V USB Port VGA VGA Port PCI-EX4*2 BCM57710 10GB/s P0,P1,P2,P3 PCI-EX4 2GB/s PCI-EX4 2GB/s 4.3 Power Supply USB1.
Functional Description 4.3.1 GE Daughter Card GE Daughter Card The GE daughter card provides two external Ethernet interfaces; 10/100/1000M Base-T autonegotiation and RJ-45 interface. The RTM-ATCA-7350 can host one or two GE daughter cards, thus providing up to four external Ethernet interfaces. The following figure shows the GE daughter card. Figure 4-2 GE Daughter Card Network port indicator Network port indicator Indicators The GE daughter card provides two network port indicators.
FC Daughter Card Functional Description Optical modules are used to provide the optical interfaces at the face plate. See Connecting Optical Fibers on page 36 for installing the optical modules. Optical modules for the FC daughter card must be obtained separately. Recommended modules are FINISAR FTRJ8519P1BNL-HW. FINISAR FTRJ8519P2BNL-HW. The following figure shows the FC daughter card. Figure 4-3 FC Daughter Card ALM RUN ALM RUN Indicators The FC daughter card provides the RUN and ALM indicators.
Functional Description 50 FC Daughter Card RTM-ATCA-7350 Installation and Use (6806800H30F)
A Related Documentation A.1 A Emerson Network Power - Embedded Computing Documents The Emerson Network Power - Embedded Computing publications listed below are referenced in this manual. You can obtain electronic copies of Emerson Network Power - Embedded Computing publications by contacting your local Emerson sales office. For documentation of final released (GA) products, you can also visit the following website: http://www.emersonnetworkpowerembeddedcomputing.
Related Documentation 52 Related Specifications RTM-ATCA-7350 Installation and Use (6806800H30F)
