Instruction manual

ManualsBrandsEmerson ManualsFitness EquipmentROSEMOUNT NGA2000 HFID

NGA 2000 MLT Hardware

CONTENTS

Emerson Process Management GmbH & Co. OHG

Instruction Manual

90002929

07/2006

Fig. Title Page

Fig. 11-1: Principle signal processing with PCB "PSV" ................................................................. 11 - 1

Fig. 11-2: PCB "VVS" .................................................................................................................... 11 - 2

Fig. 11-3: PCB "MOP” (partial view).............................................................................................. 11 - 3

Fig. 11-4: PCB "BHZ” (position of signal LED's / heating transistors) ........................................... 11 - 6

Fig. 11-5: PCB "DSP01” ................................................................................................................ 11 - 7

Fig. 11-6: LEDs on component side of PCB "DSP01” ................................................................... 11 - 8

Fig. 11-6a: LEDs “V7” and “V9” (PCB "DSP01”) ............................................................................. 11 - 8

Fig. 11-6b: LEDs “V3” and “V4” (PCB "DSP01”) ............................................................................. 11 - 9

Fig. 11-6c: LEDs “V12” to “V17”, Jumper “P40” (PCB "DSP01”) .................................................... 11 - 9

Fig. 11-7: Soldering pads on soldering side of PCB "DSP01” ..................................................... 11 - 10

Fig. 11-7a: Soldering pad “LB1” and “LB2 (PCB "DSP01”) ........................................................... 11 - 10

Fig. 11-7b: Soldering pad “LB18” (PCB "DSP01”) ........................................................................ 11 - 10

Fig. 11-8: Schematic diagram of inspection of PCB "DSP01” ..................................................... 11 - 11

Fig. 11-9: Soldering pad “DEF/LB3” (PCB "DSP01”) .................................................................. 11 - 12

Fig. 12-1: Controller Board ACU (partial view, component side)................................................... 12 - 3

Fig. 12-2: Fuses MLT 2 (partial inside view, drawing without front panel)..................................... 12 - 5

Fig. 12-3a: Fuses PCB LEM 01 (component side) .......................................................................... 12 - 6

Fig. 12-4a: Power Supply for UV Source (front view, front panel disassembled) ............................ 12 - 8

Fig. 12-4b: UV Source and PCB ESP10 (top view, housing cover disassembled) ......................... 12 - 9

Fig. 14-1: Leak Testing with an U - Tube - Manometer ................................................................. 14 - 1

Fig. 15-1: MLT 1 (Plattform housing) Fastening screws housing cover ........................................ 15 - 2

Fig. 15-2: MLT 1 (Plattform housing) Fastening screws front panel.............................................. 15 - 3

Fig. 15-3: MLT 1 (1/2 19" housing) Fastening screws housing cover ........................................... 15 - 4

Fig. 15-4: MLT 1 (1/2 19" housing) Fastening screws front panel ................................................. 15 - 5

Fig. 15-5: MLT 2 (Field housing) fastener for front panel .............................................................. 15 - 7

Fig. 15-6: MLT 2, photometer carriage slide ................................................................................. 15 - 7

Fig. 15-7: MLT3 (standard version) / MLT 4 (1/1 19" housing) Fastening screws front panel ....... 15 - 8

Fig. 15-8: MLT3 (gas purity measurement) (1/1 19" housing) Fastening screws front panel ........ 15 - 9

Fig. 15-9: Cat 200 Enclosure Assembly ...................................................................................... 15 - 11

Fig. 15-10: Cat 200 Junction box .................................................................................................. 15 - 12

Fig. 15-11: CAT 200 Dome, fixing screws ..................................................................................... 15 - 13

Fig. 15-12: View at analyzer module ............................................................................................. 15 - 14

Fig. 15-13: Plate with detents........................................................................................................ 15 - 14

Fig. 15-14: CAT 200, Cast Iron housing, Interior View .................................................................. 15 - 15

Fig. 17-1: Photometer Assembly, example (Top view, detail) ....................................................... 17 - 2

Fig. 17-2: Chopper Housing with IR light sources ......................................................................... 17 - 3

Fig. 17-3: Photometer Assembly (1 mm to 10 mm analysisi cells) ................................................ 17 - 4

Fig. 17-4: Photometer Assembly (30 mm to 200 mm analysisi cells) ............................................ 17 - 4

Fig. 18-1: PCB “OXS”, assembled, horizontal projection .............................................................. 18 - 3

Fig. 18-2: MLT 1, front panel, rear view ........................................................................................ 18 - 4

Fig. 18-3: PCB “OXS”, assembled, horizontal projection .............................................................. 18 - 6

LIST OF FIGURES