QUICK INSTALLATION GUIDE (v. 1.
WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Adopt necessary measures to run the system in an environment free of electromagnetic disturbs. The system is capable to restore its functionality after a failure due to electromagnetic disturbs if they do not damage or alter the device.
Contents 1. CHECK LIST .............................................................................................. 5 2. INSTALLATION.......................................................................................... 6 3. MAINTENANCE ......................................................................................... 8 4. RS 485 CONNECTION .............................................................................. 9 The TTL output ....................................................
1. CHECK LIST Before installing and configuring the XWEB system we recommend checking its package to verify it contains: 1 XWEB unit; 1 Quick reference manual (Fast installation); 1 CDROM containing the Operating manual; 1 Power cord for power supply connection; 1 PS2 Splitter for mouse and keyboard; 2 Mounting brackets; 4 Rubber feet and 3 jumpers; Detachable screw connectors (1x2 ways+1x3 ways; 1x6 ways); 8 Screws, 3,5mm X 6,5mm; Figure 1 1592010860 XWEB5000 stp GB r1.
2. INSTALLATION Do not open XWEB. Its opening makes its warranty invalid. However, to install XWEB you need: One blade and one cross screwdrivers Mouse PS2 Keyboard PS2 Standard VGA screen (no high definition/HDMI) To install XWEB, please refer to the picture below which represents the back of XWEB. Apply then following procedure: 1. XWEB has grounding receptacle. Verify the implant in which it will be connected to adopt electrical ground protection; 2. Fix XWEB at its operating position.
Figure 2 RS485 NETWORK: always use the indicated polarity; total length shall not exceed 1000m; electric line shall not spit or use starconnections; avoid proximity of electric power sources; usage of shielded cable. Its wires shall be 0.5 mm2 minimal section. Shield shall not be connected. Belden 8772 cables are reccomended. Connect a terminal line resistor (120 Ohm, 1/4 W) on the most distant device. Resistor shall connect + and – of its serial connector. Technical details Power supply 110 ..
3. MAINTENANCE In any case, like maintenance or cleaning or move, XWEB shall not be open. Warranty expires on opening it. Apply following procedure referencing to XWEB rear picture introduced in previous paragraph: 1. At first, press and release power on/off button (2); 2. Wait until all frontal LEDs go off including PWR; 3. Disconnect external modem if present (7); 4. Disconnect printer if present (6); 5. Disconnect monitor, keyboard and mouse (5); 6. Disconnect telephonic and/or LAN cables (4); 7.
4. RS 485 CONNECTION The cable must have 2 or 3 wires with shield, minimum section 0,5mm2 (ex. BELDEN 8772). From the XWEB position the cable reaches all the instrument positions. Do not execute loops or derivations. 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Right connection: Figure 3 Wrong connection: Figure 4 Always keep the serial cable away from power cables. Always keep the serial cable away from Electro-magnetic or frequency sources. Do not connect shield to ground. Do not connect the “Gnd (ground)” terminal. Remember to draw a map of the line. This will help you to find errors if something is wrong. The instrument with RS485 have “+” and “-“ terminals, respect the polarity.
The TTL output The instrument with RS485 on board does not need any kind of external interface module. For instruments with an external interface: keep the TTL cable away from power cables or frequency sources. The XJ485 external interface must be connected with a TTL cable to the instrument with TTL compatibility. Serial address of the instruments Each instrument must be defined by its unique address. Check the address into the Adr parameter value of each instruments.
5. Local connection with monitor, mouse and keyboard On rear of the XWEB3000 sockets are provided for a monitor, a mouse and a keyboard. Please connect all the peripherals before powering-on the unit otherwise the system may fails to recognise them. This means that , for example, if you do not plug the monitor cable in now, you won’t see anything displayed on it later.
If necessary check the instructions manual of each device connected to the unit. Figure 5 The operative procedure to work with XWEB3000 is the same for all connection methods. It is possible to connect to the unit via a single PC provided with LAN card, by using the net connector RJ 45 (LAN). Due to the PC-client power, this kind of connection is more suitable for the setup procedures. the cable between the Server and the PC must be with crossing wires (“Bridge Cable”).
WINDOWS XP TCP/IP SETUP Click on Start button, chose Control panel, click on “Network and internet connections” icon: Figure 6 Then chose “Network connections”: Figure 7 The following windows will appear: Figure 8 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Right mouse click on network interface icon, then chose “Properties”: Figure 9 The following windows will appear: 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Figure 10 Select “Internet Protocol (TCP/IP)”, then click on Properties. The following windows will appear: Figure 11 Fill those fields with values indicated in the picture. Press ‘OK’ to confirm to finish with this procedure. 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
WINDOWS 7 TCP/IP SETUP Following procedure is illustrated with Windows7 standard visualization mode. If your system works with a different visualization mode and you have difficulties to follow following instructions then ask for support to an expert operator. Despite the visualization mode the procedure is however the same. All the following instructions are to be executed with the usage of the left-mouse button only (where red hand icon indicates).
Open ‘Network and Internet’ Figure 13 Open ‘Network and Sharing Center’ 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Figure 14 Click on ‘Local Area Connection’ Figure 15 Click on ‘Properties’: 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Figure 16 Insert administrative username and password if prompted. Select ‘Internet Protocol Version 4 (TCP/IPv4)’ and click ‘Properties’. Figure 17 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Fill following window using values indicated in Figure 18. Figure 18 Click ‘OK’ to confirm and to finish with this procedure. 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
6. Modem connection (“or point to point connection”) It represents the most common method where the LAN (intranet / Ethernet / internet) is not available. It is strongly advised to use a dedicated telephone line. IMPORTANT: Use exclusively modem devices approved by Dixell. Remember that many modems are not compatible with Linux. The list of compatible models can be found under the menu: ConFiguretion – System - Modem.
SETTING UP DIAL-UP CONNECTION FOR WINDOWS XP In Windows XP, you will use the "New Connection Wizard". 1. From the Start menu, select Control Panel. Figure 19 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
2. If Control Panel is set for "Classic View", double-click on the Network Connections icon. Figure 20 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
3. If Control Panel is set for "Category View", select the "Network and Internet Connections" category, then double-click on the Network Connections icon. Figure 21 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Figure 22 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
4. Under Network Tasks, select "Create a new connection". Figure 23 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
5. Click "Next". Figure 24 6. Click "Next" at the bottom of this page to continue with the setup instructions. 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
7. Select "Connect to the Internet" and click "Next". Figure 25 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
8. Select "Set up my connection manually" and click "Next". Figure 26 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
9. Select "Connect using a dialup modem" and click "Next". Figure 27 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
10. Type "XWEB3000 DIRECT MODEM" in the ISP Name box and click "Next". Figure 28 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
11. Type the access number in the Phone Number box. E.G: If telephone number is 555789 and area code is 099, put this Telephone number: 099555789. If there is a switching machine and you have to dial a digit to get the line ( 0 or 9 for example, it depends on the switching machine), put this telephone number: 0, 099555789 or 9, 099555789. Click "Next". Figure 29 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
12. Type dialup account name dixell in the User Name box. Type dialup password dixell in the Password and Confirm Password boxes. We recommend that you check the first 2 checkboxes, but not the 3rd box which turns on the Internet Connection Firewall. Click "Next". Figure 30 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
13. Place a tick in the box to create a shortcut on your desktop, and click "Finish". Figure 31 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
14. You are now ready to connect to your XWEB3000. If you want to dial your XWEB3000 DIRECT MODEM connection automatically when you start Internet Explorer, do the following. Start Internet Explorer, and select "Internet Options" from the "Tools" menu. Select the "Connections" tab. Make sure that XWEB3000 DIRECT MODEM is your default connection (if not, highlight it and click "Make Default"). Make sure that the "Always dial my default connection" option is selected. Figure 32 1592010860 XWEB5000 stp GB r1.
SETTING UP DIAL-UP CONNECTION FOR WINDOWS 7 Following procedure is illustrated with Windows7 standard visualization mode. If your system works with a different visualization mode and you have difficulties to follow following instructions then ask for support to an expert operator. Despite the visualization mode the procedure is however the same. All the following instructions are to be executed with the usage of the left-mouse button only (where red hand icon indicates).
Open ‘Network and Internet’ Figure 34 Open ‘Network and Sharing Center’ 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Open ‘Set up a new connection or network: Figure 35 Open ‘Set up a dial-up connection’ 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Figure 36 In case the modem is not yet attached to XWEB, choose option to run unconditioned conFiguretion. Figure 37 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
1592010860 XWEB5000 stp GB r1.1 2012.06.22.
Type access number. E.G: If telephone number is 555789 and area code is 099, put this Telephone number: 099555789. If there is a switching machine and you have to dial a digit to get the line ( 0 or 9 for example, it depends on the switching machine), put this telephone number: 0, 099555789 or 9, 099555789. Insert also appropriate username and password and name the connection to reuse it avoiding to configuring it again in the future. Figure 38 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
7. Intranet / ethernet connection The Intranet or Ethernet connection should be initially managed by the net administrator which will assign one free IP address to reach the Server. This number is an example of what you should expect: http://192.168.000.111 . After receiving the address from your network Administrator the XWEB3000 must be set with this number. REMEMBER: A setup wizard will guide you through the procedure. Please ensure you have an IP address to use in network section.
Internet connection It is necessary to have a STATIC IP address for the XWEB3000 which is normally assigned by the Provider of your internet services (ISP). The Internet connection allows XWEB3000 to be reached from all PC-clients. Insert the net address assigned by the administrator into the Browser address bar. Bookmark the address with personalised name for the future connections. Ask your provider for more details about the rent of a the static IP.
If working with the router GATEWAY and DNS check your Internet contract details. Depending on your network topology you may need a reversing NAT on port 80. It is not enough to link port 80 on Router side to port 80 on intranet side. Some firewall or Router need also di reverse setup. 1592010860 XWEB5000 stp GB r1.1 2012.06.22.
8. Troubleshooting Guide Problem Solution The log-in page doesn’t load Check your browser setup. My password doesn’t allow me to log-in. Beware to the caps-lock button an capitol letters. Is it your password correct? My browser XWEB3000 log-in page can’t reach Check cable typology From windows go to Start->Run… ping 192.168.0.200 –t A continuous set of information should be appear. Someone in the intranet/LAN receive a warning XWEB3000 uses the same message about an IP conflict.
9. Unit Setup Reminder Please take some moments to make an hardcopy of this page, then compile it and store it near XWEB3000 unit.
Notes _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ _________________________________________________________________ ____________________________________________
