Brochures and Data Sheets

NetSure
™
ACU+ Controller (Advanced Control Unit Plus)
User Instructions, UM1M820BNA (Issue AK, March 3, 2014)
Spec. No: 1M820BNA, 1M820DNA Code: UM1M820BNA
Model No: M820B, M820D Issue AK, March 3, 2014
82
Figure 9. Local Menu Flow Diagrams (cont’d from previous page, cont’d on next page)
Power System
G
e
ne
r
al
Po
wer S
pl
it
Slave Curr Lmt
60 % (10-90)
Delta Volt
0.5 V (0.1-2.0)
Proportion Coeff
30.0
(0
-100
)
I
nteg
ra
l Tim
e
60 s
(10-2000)
ENT
ENT
ES
C
E
SC
ESC
B2
E
NT
Po
wer S
plit
To C
ha
nge a
Para
me
ter:
P
ress
or
to move up and
do
wn li
st of parameters.
P
ress
EN
T to highlight selected parameter.
Press or to change highlighted value.
Press ENT to make the change.
Press ESC to cancel the chan
ge
.
The parame
te
r val
ue
s sho
wn in
( ) ar
e the
adjustment
r
ang
e or
acce
pta
ble
values.
F
actory de
fault
settings are listed in
the
ACU+ C
onfig
uration D
rawing (
C-dwg)
fu
rnish
ed with y
our syste
m.
To
Sele
ct
a Sub
-Men
u:
P
ress
or to move cursor in
men
u s
cree
n (selects menu item).
Press ENT to enter selected sub-menu.
Auto/Man State
Auto (a
u
to
/ m
a
nu
al
)
Manual Mode Lmt
1 h (
0-24
)
Mtnc Cycle Time
3
60 da
ys
(10-
7200
)
EStop/EShutdown
D
isab
le
d (di
sa
bled
/ ESt
op
/ ESh
utdo
wn
)
Load Curr Alarm
300
0 A
(0-4
00
0)
A
larm
Bloc
ke
d
Nor
mal (normal / blocked)
Rect Expansion
Inactive (inactive / primary / secondary)
Address (Slave)
201 (201 / 202 / 203)
Over Voltage 1
57.0 V (40-60) (20-30)
O
ver V
ol
tage
2
58.0 V (
40-6
0)
(20-
30
)
U
nd
er Vo
ltag
e 1
4
8.0 V
(40-60) (20-30)
Und
er
Volt
ag
e 2
4
4.
0 V (40-60) (20-30)
Fail
Safe
e
na
ble (disable / enable)
Hybrid Mode
disable (disable / fixed daily / capacity)
DG Run Overtemp
enable (disable / e
na
ble)
DG Run Time
6
0 min
(30-
12
0)
DG Us
ed
D
G1 (D
G1 / D
G2 / Both)
D
I for
Gr
id
DI3
(DI1 / ... / DI8)
D
OD
40.0 % (20-80)
Dsch Duration
12 hours (1-22)
Start Dsch Time
19 clock (0-24)
High Load Set
40.
0 %
(20-80)
E
qua
l Sta
rtT
ime
8 clo
ck (0-
24)
DG Alarm De
lay
60 se
c. (30-18
0)
Fail Safe
Normally Open (normally open / no
rmally c
lose)
Co
ntactor
Mode
Master Ctrlr (M
aster Ct
rlr / S
lave Ctrl
r)
Relay Test
Disabled (d
isabled
/ auto
matic / i
ndividual)
Relay Test T
ime
45 se
c. (0-120
)
HighLoadLevel1
70% (
0-100)
HighLoadLevel2
85% (0-100)
DI1 Al
arm Stat
e
H
igh (Low / High)
...
DI8 Alar
m State
High (L
ow / Hi
gh)
A
mb
Temp Senso
r
IB2
T2 (None / SMTemp8 T8 / ... / SMTemp8 T1 /
... /
SMTemp1 T8 / ...
/ SMTem
p1 T1 / EIB T2 / EI
B T1 /
IB2 T2 / IB2 T1 /
System
T3 / System T2 / Sy
stem T1 /
Average / Max
imum)
Amb Temp High2
100.0 deg. C (-40 t
o +100)
Amb Temp
High1
90.0 deg
. C (-40 to +100)
Amb Temp Low
-10.0
deg. C (-40 to +100
)
System Temp
1
None
(None / Battery / Ambient)
System Temp2
None (None / Batt
ery / Ambient)
System Temp3
None (None / Battery / Ambien
t)
IB2 Temp1
Ba
ttery (None / Battery
/ Ambient)
IB2 Temp2
Ambient (None / B
attery / Ambient)
EIB Temp1
None (Non
e / Battery / Ambient)
EIB Temp2
None (None / Battery / Amb
ient)
Special
Configurations
O
nly
General
The t
emperature
monitore
d by the
Temp. Probe
sele
cted
here is displayed on
the Homepa
ge of
the We
b Interface.