MVME7616E Transition Module Installation and Use 6806800A43B August 2008
© Copyright 2008 Emerson All rights reserved. Trademarks Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. © 2008 Emerson Electric Co. All other trademarks are the property of their respective owners. Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4.7.1 4.7.2 4.7.3 4.7.4 4.7.5 4 3-Row P2 Adapter (J2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-Row P2 Adapter (J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-Row P2 adapter (J1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PMC I/O, 5-Row P2 Adapter (J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables Table 1-1 Table 1-2 Table 1-3 Table 1-4 Table 1-5 Table 1-6 Table 3-1 Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 4-6 Table 4-7 Table 4-8 Table 4-9 Table 4-10 Table 4-11 SIM Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MVME761 Transition Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-Row P2 Adapter Connectors (MVME761-001) . . . . . . . . . . . . . . . . . . . . . . .
List of Tables 6 MVME7616E Transition Module Installation and Use (6806800A43B)
List of Figures Figure 1-1 Figure 1-2 Figure 1-3 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 RTM Front Panel and Components Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Three Row P2 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Five Row P2 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Figures 8 MVME7616E Transition Module Installation and Use (6806800A43B)
About this Manual Overview of Contents This manual is divided into the following chapters and appendices: Chapter 1, General Information Chapter 2, Hardware Preparation and Installation Chapter 3, Functional Description Chapter 4, Connector Pin Assignments MVME7616E Transition Module Installation and Use provides general information, hardware preparation, installation instructions and support information for the MVME7616E-001 and MVME7616E-011 Transition Modules.
About this Manual Abbreviations This document uses the following abbreviations: Abbreviation Description AC Alternating Current CFM Cubic Feet per Minute D/C Direct Current DCE Data Communications Equipment DIN Deutsches Insitut für Normung eV DTE Data Terminal Equipment EMI Electro-Magnetic Interference ESD Electro-Static Discharge FCC Federal Communications Commission GND Ground I/O Input/Output IC Integrated Circuit IEEE Institute of Electrical and Electronics Engineers PMC
About this Manual Notation Description File > Exit Notation for selecting a submenu Notation for variables and keys [text] Notation for software buttons to click on the screen and parameter description ... Repeated item for example node 1, node 2, ..., node 12 . Omission of information from example/command that is not necessary at the time being . . .. Ranges, for example: 0..
About this Manual Comments and Suggestions We welcome and appreciate your comments on our documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to us by filling out the following online form: http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form In “Area of Interest” select “Technical Documentation”. Be sure to include the title, part number, and revision of the manual and tell us how you used it.
General Information 1.1 1 Overview This manual provides general information, hardware preparation, installation instructions, and a functional description for the MVME761-001 and MVME761-011 Transition Modules. The MVME761-0x1Transition Module provides the interface between the MVME5100 or MVME5500 Single Board Computer VMEmodules and various peripheral devices. This module provides industry standard connectors to simplify customer cable requirements for the serial port, printer, and Ethernet signals.
General Information Serial Port Interface Modules Figure 1-1 shows the MVME761 transition module component layout and the front panel. See Table 1-2 for a list of the front panel port connectors. Figure 1-1 RTM Front Panel and Components Side MVME 761-001 COM1 J5 COM2 J6 DTE 1 DCE J2 3 SERIAL 3 60 J1 59 2 1 J7 SERIAL 4 60 J12 59 2 1 J8 DTE DCE J3 1 3 PARALLEL J4 P2 10/100 BASET J9 1910 9609 1.
P2 Adapter Boards General Information The SIMs for the MVME761 are listed in the following table. Table 1-1 SIM Part Numbers Interface Model Number Part Number EIA-232-D DCE SIM232DCE5E 01-W3876B11A EIA-232-D DTE SIM232DTE5E 01-W3877B11A Additional SIMs may be released. Please see your Emerson representative for a complete list of SIMS that are available for the MVME761-0x1. 1.
General Information 1.7 Five-Row P2 Adapter (MVME761-011) Five-Row P2 Adapter (MVME761-011) The P2 adapter for the MVME761-011 mounts onto a 5-row, 160-pin P2 backplane connector. The 68- pin female connector, J1, carries 16-bit SCSI signals from the host VMEmodules. It also has a 64-pin male connector, J3, for PMC I/O.
Connectors and Cables General Information Table 1-2 MVME761 Transition Module Connectors (continued) Type Number Description Parallel port J4 36-pin female parallel port connector 10Base-T, 100Base-TX J9 8-pin female RJ-45 Ethernet port connector SIM J1, J12 60-pin female connector VME P2 64-pin male connector to J2 on the P2 adapter Table 1-3 3-Row P2 Adapter Connectors (MVME761-001) Type Number Description VME P1 96-pin female DIN 41612 connector to the chassis backplane J3 64-pin
General Information 1.9 Specifications Specifications The MVME761 transition module specifications are shown in the next table.
Hardware Preparation and Installation 2.1 2 Overview This chapter provides unpacking instructions, hardware preparation, and installation instructions for the MVME761 transition module, the P2 adapter, and the Serial Interface Modules (SIMs). 2.2 Unpacking the Hardware The MVME761 is packed in an antistatic wrapper to protect it from static discharge. Emerson strongly recommends that you use an antistatic wrist strap and a conductive foam pad when handling the equipment.
Hardware Preparation and Installation Installing the Serial Interface Modules You must set the jumpers and install the SIMs prior to installing the MVME761 transition module in the system chassis.The SIMs plug into connector J1 (for serial port 3) or J12 (for serial port 4) on the MVME761 transition module. Figure 2-2 SIM Configuration Mounting Hole P1 Alignment Key Mounting Hole 11637 9610 Procedure Install the SIMs on the MVME761 transition module per the following procedure: 1.
Installing the Serial Interface Modules Hardware Preparation and Installation Do not force the SIM onto the transition module. 4. Secure the SIM to the transition module standoffs with the two Phillips-head screws provided. Do not over tighten the screws.
Hardware Preparation and Installation 2.4 Installing the Transition Module and P2 Adapter Installing the Transition Module and P2 Adapter Install the MVME761 transition module and P2 adapter in the system chassis. The P2 adapter is required because the P2 connector on the transition module is not compatible with the P2 connector on the chassis backplane.
Installing the Transition Module and P2 Adapter Figure 2-4 Hardware Preparation and Installation Chassis Connections VME BACKPLANE Host Board MVME761 Transition Module P1 30-W2799B02A 64-CONDUCTOR P2 ADAPTER P2 P1 P2 J3 ON THE 3-ROW P2 ADAPTER J4 ON THE 5-ROW P2 ADAPTER ENCLOSURE BOUNDARY 11654.00 9610 Procedure Follow these steps to configure, install, and cable the transition module. 1. Turn all equipment power OFF and disconnect the power cable from the AC power source. 2.
Hardware Preparation and Installation Installing the Transition Module and P2 Adapter 8. Attach the 64-conductor cable (furnished with the MVME761-0x1) to the P2 adapter (J3 on the 3-row version, J4 on the 5-row version). Be sure to orient cable pin 1 with connector pin 1. 9. Attach the 64-conductor cable to connector P2 on the transition module. Be sure to orient cable pin 1 with connector pin 1. 10.Insert the transition module into the chassis slot, and tighten the attaching screws.
Functional Description 3.1 3 Overview This chapter provides information on MVME761 transition module and SIM circuitry, P2 signal multiplexing, and the configuration of the serial ports. 3.2 Circuitry The MVME761 transition module and the Serial Interface Modules (SIMs) convert the TTL level signals to and from the MVME5100, and MVME5500 modules to the reception and transmission levels specified by the appropriate port interface standard.
Functional Description Circuitry The block diagram for the MVME761 transition module is shown in Figure 3-1. The block diagram for the 3-row DIN backplane P2 adapter is shown in Figure 3-2. The block diagram for the 5-row DIN backplane P2 adapter is shown in Figure 3-3. Figure 3-1 Transition Module Block Diagram 10Base-T 100Base-TX Parallel COM1 COM2 Serial 3 Serial 4 Serial Interface Module (SIM) Serial Interface Module (SIM) Buffers EIA-232-D P2 Multiplex Function 64-Pin DIN Connector 11638.
P2 Signal Multiplexing (P2MX) Figure 3-3 Functional Description 5-Row DIN Backplane P2 Adapter Block Diagram 16-bit Single-ended SCSI SCSI Terminators 64-pin Connector to MVME761 Transition Module PMC I/O 5-Row Backplane Connector 11752.00 9703 3.3 P2 Signal Multiplexing (P2MX) Because of a limited number of pins on the P2 connector, both the VME processor board and the MVME761 transition module multiplex and demultiplex some of the P2 signals.
Functional Description P2 Signal Multiplexing (P2MX) Sixteen time slots are defined and allocated. The signal multiplexing sequences are listed in the following table..
Serial Interface Module Circuitry Functional Description The timing relationships among MXCLK, MXSYNC#, MXDO, and MXDI are illustrated in the next figure. Figure 3-4 Multiplex Signal Timing Chart Time Slot 15 Time Slot 0 Time Slot 1 Time Slot 2 Time Slot 3 MXDO Reserved RTS3 DTR3 LLB3 RLB3 MXDI DCD2 CTS3 DSR3 DCD3 TM3 MXCLK MXSYNC# 11640.00 9611 3.
Functional Description 3.5 COM1 and COM2 Asynchronous Serial Ports COM1 and COM2 Asynchronous Serial Ports The asynchronous serial port (COM1 and COM2) configuration is shown in the next figures..
Asynchronous/Synchronous Serial Ports 3.6 Functional Description Asynchronous/Synchronous Serial Ports The asynchronous/synchronous serial port (Port 3 and Port 4) interface configuration diagrams are on the following pages.
Functional Description Asynchronous/Synchronous Serial Ports Figure 3-7 EIA232-DCE Configuration Port 4 VME MODULE MVME761 Z85230 SCC EIA232-DCE SIM HD26 TXD 3 RTS# 5 RXD 2 CTS# 4 DCD# 20 J17 J19 J3 1 2 3 2 3 1 15 17 J16 TRXC 1 2 RTXC 3 24 P2/P2MX DCE Z8536 CIO DTR# 8 LLB# 25 RLB# 22 DSR# 6 RI# 21 TM# 18 7 Headers: J16 2-3 J17 1-2 J19 1-2 32 Header J3 2-3 MVME7616E Transition Module Installation and Use (6806800A43B)
Asynchronous/Synchronous Serial Ports Figure 3-8 Functional Description EIA232-DTE Configuration Port 3 VME MODULE MVME761 Z85230 SCC EIA232-DTE SIM HD26 TXD 2 RTS# 4 RXD 3 CTS# 5 DCD# 8 J18 TRXC J2 3 2 3 1 1 24 2 15 17 RTXC P2/P2MX DTE Z8536 CIO DTR# 20 LLB# 18 RLB# 21 DSR# 6 RI# 22 TM# 25 7 Header J18 2-3 MVME7616E Transition Module Installation and Use (6806800A43B) Header J2 1-2 33
Functional Description Figure 3-9 Asynchronous/Synchronous Serial Ports EIA232-DTE Configuration Port 4 MVME761 VME MODULE Z85230 SCC EIA232-DTE SIM HD26 TXD 2 RTS# 4 RXD 3 CTS# 5 DCD# 8 J17 J19 J3 1 2 3 3 1 24 2 15 J16 TRXC 1 2 RTXC 3 17 P2/P2MX DTE Z8536 CIO DTR# 20 LLB# 18 RLB# 21 DSR# 6 RI# 22 TM# 25 7 Headers: J16 2-3 J17 2-3 J19 1 2 34 Header J3 1-2 MVME7616E Transition Module Installation and Use (6806800A43B)
Connector Pin Assignments 4.1 4 Overview This chapter provides the pin assignments for the P2 connector and front panel port connectors on the MVME761 transition module, as well as for the SCSI and PMC I/O connectors on the P2 adapters. 4.2 P2 Connector Signaling and power from the host VMEmodules are received through connector P2, a 64-pin DIN connector.
Connector Pin Assignments Asynchronous Serial Port Connectors (J5/J6) Table 4-1 P2 Connector Pin Assignments (continued) Row A Pins 4.
Asynchronous/Synchronous serial Port connectors (J7/J8) 4.4 Connector Pin Assignments Asynchronous/Synchronous serial Port connectors (J7/J8) The interface for the asynchronous/synchronous serial ports 3 and 4 is provided by two HD-26 connectors, J7 and J8. The connector shields for these ports are tied to chassis ground. The pin assignments and signal mnemonics for serial ports 3 and 4 are listed in the following tables.
Connector Pin Assignments Parallel I/O Port Connector (J4) Table 4-4 Serial Port 4 Pin Assignments (continued) 4.5 Pin Signal Pin Signal 13 SP4_P13 26 No Connect Parallel I/O Port Connector (J4) The interface for the parallel port is a standard IEEE P1284-C, 36-pin connector, J4. The functionality of each signal depends on the mode of operation of this bidirectional Parallel Peripheral Interface. Refer to the IEEE P1284 D2.00 Standard for a complete description of each signal function.
Ethernet Connector (J9) 4.6 Connector Pin Assignments Ethernet Connector (J9) The 10Base-T/100Base-TX Ethernet interface is a RJ-45 connector, J9. The connector shield is tied to chassis ground. The pin assignments and signal mnemonics for this connector are listed in Table 4-6. Table 4-6 10Base-T/100Base-TX Pin Assignments Pin Signal 1 TD+ 2 TD- 3 RD+ 4 Terminated 5 Terminated 6 RD- 7 Terminated 8 Terminated 4.7 P2 Adapter Connectors 4.7.
Connector Pin Assignments 3-Row P2 Adapter (J3) Table 4-7 8-bit SCSI Connector (3-Row P2 adapter) (continued) 4.7.2 Pin Signal Signal Pin 13 GND ACK 38 14 SDB6 GND 39 15 GND RST 40 16 SDB7 GND 41 17 GND MSG 42 18 DBP GND 43 19 GND SEL 44 20 GND GND 45 21 GND D/C 46 22 GND GND 47 23 GND REQ 48 24 GND GND 49 25 No Connect O/I 50 3-Row P2 Adapter (J3) The pin assignments and signal mnemonics for this connector are listed in Table 4-8.
5-Row P2 adapter (J1) Connector Pin Assignments Table 4-8 VME Connector (3-Row P2 adapter) (continued) 4.7.
Connector Pin Assignments PMC I/O, 5-Row P2 Adapter (J3) Table 4-9 16-bit SCSI Connector (5-Row P2 adapter) (continued) 4.7.
5-Row P2 adapter (J4) Connector Pin Assignments Table 4-10 PMC I/O Connector (5-Row P2 adapter) (continued) 4.7.
Connector Pin Assignments 5-Row P2 adapter (J4) Table 4-11 VME Connector (3-Row P2 adapter) (continued) 44 Pin Signal Signal Pin 3 T+ TXD1 35 4 T- GND 36 5 R+ RXD1 37 6 R- GND 38 7 PRSTB_L RTS1 39 8 +12VF GND 40 9 PRD0 GND 41 10 GND CTS1 42 11 PRD2 GND 43 12 PRD1 TXD4 44 13 PRD4 GND 45 14 PRD3 RXD4 46 15 PRD6 GND 47 16 PRD5 RTS4 48 17 GND GND 49 18 PRD7 TRXC4 50 19 GND DTR4 51 20 PRACK_L CTS4 52 21 PRPE GND 53 22 PRBSY DCD
Index Numerics 100Base-TX 13, 39 10Base-T 13, 39 A asynchronous serial port signals 36 asynchronous/synchronous serial port configurations 31 signals 37 B backplane connector 15, 16 C cables 64-line flat ribbon 17 EIA-232 17 modem 17 P2 adapter 15 printer 17 shielded 18 circuitry MVME761 25 SIMs 29 Class A equipment 18 COM1/COM2 pin assignments 36 connectors 16 MVME761 J4, parallel port 38 J5/J6, serial ports 36 J7/J8, serial ports 37 J9, Ethernet 39 P2 35 RJ-45 39 P2 adapter 3-row J2, SCSI connector 39
parallel port signals 38 part numbers P2 adapter, 3-row 15 P2 adapter, 5-row 16 SIM 14 pin assignments 35 Ethernet connector J9 39 P2 connector (MVME761) 35 parallel port J4 (MVME761) 38 PMC I/O, J3 (P2 adapter 5-row) 42 SCSI connector J2 (P2 adapter 3-row) 39 SCSI, J1 (P2 adapter 5-row) 41 serial port (MVME761) 36 serial port 3/4 (MVME761) 37 VME connector J4 (P2 adapter 5-row) 43 VME connector, J3 (P2 adapter 3-row) 40 pin compatibility for P2 connectors 35 PMC I/O 16 PMC I/O connector (P2 adapter 5-row)
