Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[88 of 149]
Limit 2 Notification Code: current info
Limit 2 Notification Code:
55. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes the
severity of this alarm or event condition, then press
ENTER
.
CR - critical alarm NA - not alarmed
MJ - major alarm NR - not reported when event occurs
MN - minor alarm
56. The system responds with...
Limit 2 Service Effect Code: current
info
Limit 2 Service Effect Code:
57. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes how this
alarm or event affects service, then press
ENTER
.
SA = service-affecting condition, immediate action
required
NSA = nonservice-affecting condition, action required
58. The system responds with...
Alarm Class Number:
59. Type the desired alarm class number associated with the
second alarm limit, then press
ENTER
. Alarm classes are
specified with the numbers 0 through 8, with 0
representing no alarm class.
60. The system responds with...
Condition Type: current info
Condition Type:
61. This parameter applies only to TL1 commands/messages.
Type the name (20 characters maximum) which
describes this alarm or event state, then press
ENTER
.
Only alpha characters can be entered for this parameter.
TL1 uses specific values for this parameter. Refer to
TA-NWT-001360 Tables 5-1 through 5-4.
62. The system responds with...
Condition Description: current info
Condition Description:
63. This parameter applies only to TL1 commands/messages.
Type a user-defined text message (40 characters
maximum) which provides a detailed description of this
alarm, event, or condition. Then press
ENTER
. May also
be used to describe any action to be taken as a result of
the condition. All printable ASCII characters are valid
except for the percent sign (%), double quotes ("), and the
backslash (\).
64. The system responds with...
Limit 3 Enabled: current info
Limit 3 Enabled (Y or N):
65. Type
Y
to enable this alarm limit or
N
to disable this alarm
limit. Then press
ENTER
.
66. The system responds with...
Limit 3 Value: current info
Limit 3 Value:
67. Type the required value of the third alarm setting (5
digits, 20000 maximum), then press
ENTER
.
68. The system responds with...
Limit 3 Type: current info
Limit 3 Type is High or Low (H or L):
69. Type
H
if the third alarm setting is a high limit and
L
if the
third alarm setting is a low limit, then press
ENTER
.
70. The system responds with...
Limit 3 Name: current info
Limit 3 Name:
71. Type the desired name of the third alarm setting (10
characters maximum), then press
ENTER
.
72. The system responds with...
Limit 3 Notification Code: current info
Limit 3 Notification Code:
73. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes the
severity of this alarm or event condition, then press
ENTER
.
CR - critical alarm NA - not alarmed
MJ - major alarm NR - not reported when event occurs
MN - minor alarm
74. The system responds with...
Limit 3 Service Effect Code: current
info
Limit 3 Service Effect Code:
75. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes how this
alarm or event affects service, then press
ENTER
.
SA = service-affecting condition, immediate action
required
NSA = nonservice-affecting condition, action required
76. The system responds with...
Alarm Class Number:
77. Type the desired alarm class number associated with the
third alarm limit, then press
ENTER
. Alarm classes are
specified with the numbers 0 through 8, with 0
representing no alarm class.