Installation Manual

NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[83 of 149]
Initial Configuration
Note: If configuration information has been saved from another
LMS1000 by using the DOWNLOAD command, this
information can be copied into this system by using the
UPLOAD command. Refer to "Operating LMS1000" in the "User
Instructions" (Section 5847) for additional information.
Section 5847 can be accessed via the CD (Electronic
Documentation Package) furnished with your system.
Setting Local Port Communications Parameters
This procedure shows the user how to change the local port data
rate. Available local port communications parameters are shown
in Table 14.
Note: Modem port communications parameters cannot be set. The
data rate for the local port is the only communications
parameter that can be changed.
Table 14. Available Local Port Communications Parameters
Data Rate
(Bits/s)
Parity
Data
Bits
Stop
Bits
300, 600, 1200,
2400, 4800, 9600,
or 19200
n for none 8 1
Default setting shown in underlined type.
PROCEDURE:
1. After logging onto the system, type
SET COM . Then press
ENTER .
Command <6>: SET COM
2. The system displays the current communications
parameters for the local port.
bits/s, parity, data bits, stop bits.
3. The system responds with...
Enter new setup:
4. Enter a new data rate for the local port, if desired.
5. Press
ENTER to exit the command. If parameter's were
not entered, the existing settings are saved.
Setting Gateway Port Parameters (if Gateway Software Option
Installed)
This procedure shows the user how to change the Gateway port
data rate. This command also lists the settings of all Gateway port
communications parameters.
Note: The data rate for the Gateway port is the only communications
parameter that can be changed. The other communications
parameters are fixed at no parity, 1 stop bit, and 8 data bits.
PROCEDURE:
1. After logging onto the system, type
SET GATEWAY . Then
press
ENTER .
Command <6>: SET GATEWAY
2. The system displays the current communications
parameters for the Gateway port.
bits/s, parity, data bits, stop bits.
3. The system responds with...
Enter new setup:
4. Enter a new data rate for the Gateway port, if desired.
Available data rates are 300, 1200, 2400, 9600,
19200 bps (default is 9600 bps).
CAUTION!
Possible data loss may occur if the LMS1000
Gateway Port data rate is not matched to the data rate
of the LMS1000 local or modem port used to access the
customer equipment connected to the LMS1000
Gateway port.
5. Press
ENTER to accept or change the present setting and
continue. If a parameter value is not entered, the setting
is not changed.
6. The system displays the present ‘Gateway Mode Setting’
parameter and prompts for a new setting:
GATEWAY mode setting: NORMAL
New mode setting [NORMAL or GLOBAL]:
GLOBAL
7. If a different setting is desired enter the new parameter
value.
8. Press
ENTER to accept or change the present setting. If a
parameter value is not entered, the setting is not
changed saved. The system then exits the command.
Setting System Configuration
This procedure shows the user how to initially program the system
using the command SET SYSTEM. The SET SYSTEM command
steps the user through various system commands that are
normally separate commands, but are grouped together and
prompted automatically by the system. User responses to this
series of commands will program the system for its application. In
most instances, the system first lists current information, and then
prompts for new or revised information to be entered. If the
current information is accurate, the user should press
ENTER to
proceed. Refer to "Commands" in the User Instructions (Section
5847) for a typical screen display of the SET SYSTEM command.
Section 5847 can be accessed via the CD (Electronic
Documentation Package) furnished with your system.
Caution