Installation Manual

NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[1 of 149]
General Information and Installation
Checklist
Preface
This document (Section 5879) provides Installation Instructions for
Monitoring System Model
LMS1000, Spec. Nos. 586505000 and
586505500. These instructions also provide procedures for the
integrated LMS of Spec. Nos.
582140000, 582140001, and
582126100 Power Systems.
For User Instructions, refer to Section 5847 provided on the CD
(Electronic Documentation Package) furnished with your system.
Refer to SAG586505000/SAG586505500 (System Application
Guide) for additional information. The SAG can be accessed via the
CD (Electronic Documentation Package) furnished with your
system.
Note: The LMS cabinet (Spec. No. 586505000/586505500) can be
used in Vortex
®
Power Systems (VPS) and NetSure™ Power
Systems (NPS). The LMS is also factory integrated (w/out using
the Spec. No. 586505000/586505500 cabinet) into Spec. Nos.
582140000, 582140001, and 582126100 NetSure™ Power
Systems (NPS). In this document, reference to an LMS in a VPS
or NPS using the Spec. No. 586505000/586505500 cabinet
will be VPS/NPS (LMS commands and responses specific to this
interface use ‘NETSURE’). Reference to an LMS in a Spec. No.
582140000, 582140001, and 582126100 NPS Power System
will be NPS (LMS commands and responses specific to this
interface use ‘NPS’).
Installation Acceptance Checklist
Provided below is an Installation Acceptance Checklist. This
checklist helps ensure proper installation and initial operation of
the system. As the procedures presented in this document are
completed, check the appropriate box on this list. If the procedure
is not required to be performed for your installation site, also
check the box in this list to indicate that the procedure was read.
When installation is done, ensure that each block in this list has
been checked.
Note: The system is not powered up until the end of this checklist.
Note: Some of these procedures may have been performed at the
factory for you.
Installing LMS1000
 LMS1000 Display Option Installed
(586505000/586505500 only)
 Main Cabinet and Expansion Cabinet(s) Mounted in a
Relay Rack
(586505000/586505500 only)
 Optional Expansion Assembly(s) Mounted in Customer
Equipment
 Optional Modem Circuit Card Installed
 CPU Circuit Card(s) Installed
 Four Input Analog Circuit Card Installed after Making any
Jumper Adjustment as Required
 Eight Input Analog Circuit Card Installed
 Twelve Input Analog Circuit Card Installed
 Four Input Binary Circuit Card Installed
 Eight Input Binary Circuit Card Installed after Making any
Jumper Adjustment as Required
 Four Output (Form-C) Relay Circuit Card Installed after
Making any Jumper Adjustment as Required
 Eight Input Temperature Circuit Card Installed and
Ground Lead Attached to Frame Ground
 Main and Expansion Cabinets Grounding Connection
Made
(586505000/586505500 only)
 Main and Expansion Cabinets DC Input Power Connection
Made
(586505000/586505500 only)
 External CPU/Hardware Fail Alarm Connections Made
 Local Port Connections Made
 Modem Port Connections Made
 Ethernet Port Connections Made
 OEM1 Port Connections Made (586505000/586505500
only)
 OEM2 Port Connections Made (586505000/586505500
only)
 OEM3 (VPS/NPS) Port Connections Made
(586505000/586505500 only)
 Gateway Port (if available) Connections Made
 Connections Made to all Four Input Analog Circuit Cards
Installed
 Connections Made to all Eight Input Analog Circuit Cards
Installed
 Connections Made to all Twelve Input Analog Circuit
Cards Installed
 Connections Made to all Four Input Binary Circuit Cards
Installed