Installation Manual

NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[34 of 149]
Figure 13. Connection to a Twelve Input Analog Circuit Card, P/N
520838
FOUR INPUT BINARY CIRCUIT CARD P/N 506332 CONNECTIONS
Connections to a binary circuit card are made to terminal block
TB1 located at the edge of the circuit card. Refer to "Making
Connections to an LMS1000 Input/Output (I/O) Circuit Card" in this
section for terminal block TB1 connection information. Refer to
Figure 14 for terminal block pinouts.
Recommended wire size is 20-22 gauge, twisted pair wire. A
49.9Ω fusible resistor, located in each input lead, may be used to
protect leads from unintentional shorts during installation or
service. These resistors should be located as near as possible to
the voltage source to provide maximum protection.
Procedure:
1. 586505000/586505500: To access terminal block TB1
located on a binary circuit card, rotate the two captive
fasteners on the front of the cabinet until the arrow on
the fastener points up or down, and pivot the door open.
or
582140000/582140001/582126100: Open the bay's
front door.
2. Connect the leads as shown in Figure 14.
3.
586505000/586505500: If no more connections are to
be made inside the cabinet, close the cabinet door and
secure with the two captive fasteners (arrow on fastener
points towards outside of cabinet).
or
582140000/582140001/582126100: If no more
connections are to be made inside the bay, close the
bay's front door.
Figure 14. Connection to a Four Input Binary Circuit Card, P/N 506332
EIGHT INPUT BINARY CIRCUIT CARD P/N 506334 CONNECTIONS
Connections to a binary circuit card are made to terminal block
TB1 located at the edge of the circuit card. Refer to "Making
Connections to an LMS1000 Input/Output (I/O) Circuit Card" in this
section for terminal block TB1 connection information. Refer to
Figure 15 for terminal block pinouts.
Recommended wire size is 20-22 gauge. A 49.9Ω fusible resistor,
located in each single ended input lead, may be used to protect
(A1)
Analog input
wiring connection
terminals
Note:
Analog input designations A1 through A12 as shown are for
the circuit card only. The actual analog channel number
depends upon the quantity of analog and temperature
circuit cards installed and location of this analog circuit card
in the system network.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TB1
520838
unused
unused
unused
+
Terminal Battery Cell 1
+
Terminal Battery Cell 2
+
Terminal Battery Cell 3
+
Terminal Battery Cell 4
+
Terminal Battery Cell 5
+
Terminal Battery Cell 6
+
Terminal Battery Cell 7
+
Terminal Battery Cell 8
+
Terminal Battery Cell 9
+
Terminal Battery Cell 10
+
Terminal Battery Cell 11
+
Terminal Battery Cell 12
Terminal Battery Cell 1
_
(A2)
(A3)
(A4)
(A5)
(A6)
(A7)
(A8)
(A9)
(A10)
(A11)
(A12)
Note:
Binary input designations B1 through B4 as shown are for
the circuit card only. The actual binary channel number
depends upon the quantity of binary circuit cards installed
and the location of this binary circuit card in the
system network.
Binary input
wiring connection
terminals
B1
B2
B3
B4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TB1
506332