Installation Manual

NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[115 of 149]
SET UNIT
Command <6>: SET UNIT
Type
SET UNIT
, then press
ENTER
.
Unit Name:
Type the desired unit name
(30 characters maximum),
then press
ENTER
.
Unit #
Type the desired unit number
(4 digits maximum), then
press
ENTER
.
System Identifier:
Note:
This parameter does
not appear if the TL1
software option is
not installed.
This parameter applies only
to TL1 commands/messages.
Type the desired System
Identifier (20 characters
maximum), then press
ENTER
.
This data parameter is used
to identify the destination of
command messages and the
source of response and
autonomous messages in an
NMA system.
Note:
Only alphanumeric
characters are
accepted for this
parameter.
Unit Header:
Type the desired unit header
(79 characters maximum),
then press
ENTER
. The unit
header is displayed when a
user logs onto the system.
Unit Pager Code:
If required, type the desired
unit pager code (20
characters maximum), then
press
ENTER
. The Unit Pager
Code is the phone number at
which the system is located
followed by any terminating
character required. This is
the number that will appear
in the display window of the
paging system beeper unit.
Pager Delay:
Type the desired pager delay
(0-99), then press
ENTER
. The
pager delay is the time delay
(in seconds) between the last
digit dialed in a pager phone
number and outputting the
pager PIN number.
Adding and Configuring LMS1000 Expansion Nodes
This procedure shows the user how to add and configure
Expansion Nodes. Use this procedure if the system contains
586505000/586505500 Expansion Cabinets,
582140000/582140001/582126100 Secondary Bays with
LMS1000 I/O cards, and/or 586505000/586505500 Expansion
Assemblies.
Note: Refer to "Operating LMS1000" in the User Instructions
(Section 5847) for a description of nodes. Section 5847 can be
accessed via the CD (Electronic Documentation Package)
furnished with your system.
PROCEDURE:
1. After logging onto the system, type
NODE ADD . Then
press
ENTER .
Command <6>: NODE ADD
2. The system searches for and adds to the database all
Expansion Nodes found on the network. The Nodes are
arbitrarily assigned numbers prefixed with an "X". The "X"
indicates the Node is currently not configured. Also
displayed is the configuration of the Node as it was
programmed at the factory.
Searching for new nodes
Node# Name Spec. Number Ser.#
Loc Echelon Id #
X01 --- 58212190001 12346
L 1A2B3C4D5F6A
X02 --- 58212190001 12346
R 1A2B3C4D5F6B
X03 --- 58212190002 12347
L 1A2B3C4D5F6C
X04 --- 58212190002 12347
R 1A2B3C4D5F6D
3. The system then prompts to select a Node to configure.
Type the number of the Node to configure (as listed).
Press
ENTER to proceed.
Which node? : X01
4. Enter configuration information as it is displayed. Press
ENTER to proceed.
Node Number: ---
Node Number: 01
Node Name: ---
Node Name: Main Distribution Bay 1
Spec Number: 58212190001
Spec Number:
Serial Number: 12346
Serial Number:
Location Number: L
Location Number:
Module 1 List Number: --
Module 1 List Number: AB
Module 2 List Number: --
Module 2 List Number: D
Module 3 List Number: --
Module 3 List Number: T
Module 4 List Number: --