Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[104 of 149]
Note:
If "X25"or "Telnet" is selected as the REPORT DEVICE
and "TL1" is selected as the REPORT MODE, the
following statement appears if the user has any
channels configured which do not belong to an
Access Identifier group.
The following channels will be removed
from the user’s channel configuration
because they are not associated with an
access identifier:
Save changes (Y or N):
52. Type
Y
if the above entered data is to be saved in the
current user configuration and
N
if not, then press
ENTER
.
53. The system responds with...
Edit User Channels (Y or N):
54. Type
Y
if it is desired to add or delete specific system
channels from the user configuration and
N
if not, then
press
ENTER
. Channels which are a part of a user
configuration are the only channels that the system will
process for the above User Reports or TL1 report
messages. Users configured to report via a TL1 network
can only specify channels that have been configured as
part of an access identifier.
55. If "Y" was entered above, the following will be displayed...
Enter channel (e.g. A0012 or A0001-0006)
or D to display.
Add Channel:
56. Type
D
to display a complete list of channels in the user
configuration.
Type the number(s) of all additional channels to be added
to the user configuration, then press
ENTER
. Channels
can be specified by entering a single channel number
(e.g. A0001, B0008), or by entering a range of channels
(e.g. A0001-0008, L0001-0012). To exit, press
ENTER
without specifying a channel.
Note:
If "X25" or "Telnet" is selected as the REPORT DEVICE
and "TL1" is selected as the REPORT MODE, the
following statement appears if the user tries to add a
channel(s) which does not belong to an Access
Identifier group.
Channel not configured properly for TL1
reporting.
57. The system responds with...
Enter channel (e.g. A12 or A1-6) or D to
display.
Del Channel:
58. Type
D
to display a complete list of channels in the user
configuration.
Type the number(s) of the channels to be deleted from
the user configuration, then press
ENTER
. Channels can
be specified by entering a single channel number (e.g.
A0001, B0008), or by entering a range of channels (e.g.
A0001-0008, L0001-0012). To exit, press
ENTER
without
specifying a channel.
59. The system displays the second user configuration. Enter
the required data for each user as described above.
Configuring System Alarm Reporting
Note:
This information can also be programmed through the
command SET REPORT which is described later in this section.
1. The system then lists the System Alarm Reporting default
configuration, followed by...
System Alarm Report Mode (Continuous,
Single, or Off):
2. Type
Single
or
Continuous
if the system is required to
initiate an alarm report if any system channel alarms, and
Off
if not.
Note:
Single = System Alarm Report is considered
successful if the system connects with a
modem or valid Email address. (Alarm
report transmitted once.)
Continuous = System Alarm Report is considered
successful if the user issues an
ACKnowledgement. (The system
continues to issue the report at an interval
determined by the "retry time" until the
ACK command is entered by the user.)
3. The system responds with...
User Calling Sequence:
4. Type the numbers (1-8), which correspond to individual
users, in the required calling sequence, then press
ENTER
.
The user calling sequence lists the users in the order in
which the system will attempt to call or Email to
communicate an alarm report. Once the system notifies
a user, the sequence is reset to the first user, ready for
the next alarm report.
Note:
A maximum of 20 digits can be entered.
5. The system responds with...
Retry Time:
6. Type the required retry time (0-1440 minutes, with 0
representing no report retry), then press
ENTER
. The
retry time is the time interval between the calling or
Emailing of the last person designated in the user calling
sequence list and the recalling or Emailing of the first user