Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[103 of 149]
Type
Off
or
E-mail
. OFF = alarm reports are not
processed. E-mail = System Alarm Reports and User
Reports sent via Email. Then press
ENTER
.
If "X25" or "Telnet" was typed above as the Report Device,
the system responds with...
Report Mode: current info
Report Mode (Off or TL1):
Type
Off
or
TL1
. OFF = alarm reports are not processed.
TL1 = TL1 report messages processed via the TL1 port.
Then press
ENTER
.
33. The system responds with...
Report Retry Time: current info
Report Retry Time:
34. Type the number of minutes that the system will wait
before attempting to contact the user with a callback,
User Report, or TL1 report message if the prior attempt
failed (0-1440 minutes), then press
ENTER
. Zero
represents no retry. (This retry time has no effect on
System Alarm Reporting)
35. If "X25" or "Telnet" was typed above as the Report Device,
the system responds with...
TL1 Report Condition Interval: current
info
TL1 Report Condition Interval:
36. This parameter applies only to TL1 commands/messages.
Type the number of minutes (as referenced from
midnight each day) that the system will wait before
contacting the user with another Report Condition
message (0-1440 minutes), then press
ENTER
. As an
example, if a time period of 90 minutes is specified, the
system will report at Midnight, 1:30 am, 3:00 am etc. A
value of ‘0’ disables sending of Report Condition
messages.
37. If "Modem" or "Email" was typed above as the Report
Device, the system responds with...
Occurred Alarm Report: current info
Occurred Alarm Report (Y or N):
38. Type
Y
if the user requires an occurred "User Report" and
N
if not, then press
ENTER
. An occurred "User Report" is a
report of any new alarms that have occurred on the user’s
channels.
39. If "Modem" or "Email" was typed above as the Report
Device, the system responds with...
Retired Alarm Report: current info
Retired Alarm Report (Y or N):
40. Type
Y
if the user requires a retired "User Report" and
N
if
not, then press
ENTER
. A retired "User Report" is a report
of any alarms that have cleared on the user’s channels.
41. If "Modem" or "Email" was typed above as the Report
Device, the system responds with...
Persistent Alarm Report: current info
Persistent Alarm Report (Y or N):
42. Type
Y
if the user requires a persistent "User Report" and
N
if not, then press
ENTER
. A persistent "User Report" is a
periodic report of any alarms that still exist on the user’s
channels.
43. If "Y" was entered above, the system responds with...
Persistent Alarm Report Period: current
info
Persistent Alarm Report Period:
44. Type the number of minutes (as referenced from
midnight each day) that the system will wait before
contacting the user with another persistent "User Report"
(0-1440 minutes), then press
ENTER
. As an example, if a
time period of 90 minutes is specified, the system will
report at Midnight, 1:30 am, 3:00 am etc.
45. If "Modem" or "Email" was typed above as the Report
Device, the system responds with...
Daily Report: current info
Daily Report (Y or N):
46. Type
Y
if the user requires a daily "User Report" and
N
if
not, then press
ENTER
.
47. If "Y" was entered above, the system responds with...
Daily Report Command: current info
Daily Report Command:
48. Type the standard system command or user
programmable command (30 characters maximum) that
the system will issue to generate the daily "User Report",
then press
ENTER
.
49. If "Y" was entered above, the system responds with...
Daily Report Time: current info
Daily Report Time:
50. Type the desired time that the user wants to be
contacted with the daily "User Report" (format HH:MM),
then press
ENTER
.
51. The system responds with...