Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[102 of 149]
15. The primary phone number or primary Email will be used
by the system only during valid days and hours, as
programmed below.
16. The system responds with...
From Day: current info
From Day:
17. Type the beginning day of the week the user wants to be
contacted at the primary phone number for callbacks and
primary phone number or primary Email for System
Alarm Reports and User Reports (1-7, Sunday=1), then
press
ENTER
.
18. The system responds with...
Thru Day: current info
Thru Day:
19. Type the ending day of the week the user wants to be
contacted at the primary phone number for callbacks and
primary phone number or primary Email for System
Alarm Reports and User Reports (1-7, Sunday=1), then
press
ENTER
.
20. The system responds with...
From Hour: current info
From Hour:
21. Type the beginning hour of the day that the user wants to
be contacted at the primary phone number for callbacks
and primary phone number or primary Email for System
Alarm Reports and User Reports (00-23), then press
ENTER
.
22. The system responds with...
Thru Hour: current info
Thru Hour:
23. Type the ending hour of the day the user wants to be
contacted at the primary phone number for callbacks and
primary phone number or primary Email for System
Alarm Reports and User Reports (00-23), then press
ENTER
.
Note:
EXAMPLE: If 16 is entered, the primary phone # or
primary Email is used through 16:59.
24. The system responds with...
Alternate Phone: current info
Alternate Phone:
25. Type an alternate phone number the system will use for
callbacks, System Alarm Reports, and User Reports when
the current date or time is not valid as programmed
above (20 characters maximum), then press
ENTER
.
Note:
If System Alarm Reports and User Reports are to be
initiated through a pager, do not enter an alternate
phone number.
26. The system responds with...
Primary E-mail: current info
Primary E-mail:
27. Type the Email address the system is to use for System
Alarm Reports and User Reports during the "Valid Days &
Hours for Primary Phone Number", then press
ENTER
.
28. The system responds with...
Alternate E-mail: current info
Alternate E-mail:
29. Type the Email address the system is to use for System
Alarm Reports and User Reports outside of the "Valid
Days & Hours for Primary Phone Number", then press
ENTER
.
30. The system responds with...
Report Device: current info
Report Device (Modem, Ethernet, X25 [if
TL1/x.25 option installed], or Telnet
[if TL1 over Ethernet option
installed]):
31. Type the desired Report Device (select Modem, Ethernet,
X25, or Telnet) that the system uses to issue System
Alarm Reports and User Reports, then press
ENTER
.
Note:
"Modem" = LMS1000 Modem
"Ethernet" = Email notification via Ethernet Port
"X25" = TL1/X.25 Port
"Telnet" = TL1 over Ethernet Port
32. If "Modem" was typed above as the Report Device, the
system responds with...
Report Mode: current info
Report Mode (Off, Pager, M300, M1200,
M2400,M9600, M28800, M33600, or M56000):
Type the desired mode (select off, pager, modem[bits/s]
that the system uses to send System Alarm Reports and
User Reports, then press
ENTER
.
Note:
If the report mode is set to pager, enter the required
information for the primary phone number, unit
pager code, and pager delay.
If "Ethernet" was typed above as the Report Device, the
system responds with...
Report Mode: current info
Report Mode (Off or E-mail):