Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[99 of 149]
channel as described above until the system displays the
default configuration of the first relay channel.
Configuring Relay Channels
Refer to the worksheets (or copies of) located at the end of
"Installing LMS1000" as a guide in programming the various
channels associated with the system.
Note:
This information can also be programmed through the
command CONFIG R_ which is described later in this section.
Note:
Parameters which apply only to TL1 commands/messages do
not appear for configuration if the TL1 software option is not
installed.
1. After the system responds with the first relay channel
default configuration, the following is displayed...
Channel active (Y or N):
2. Type
Y
if the channel is required to be active and
N
if not,
then press
ENTER
.
3. If ”N” was entered, the system displays another relay
channel configuration. If ”Y” was entered, the system
allows the default configuration information of the
current relay channel to be changed as shown below.
4. The system responds with...
Name: current info
Name:
5. Type the desired name for this relay channel (30
characters maximum), then press
ENTER
.
6. The system responds with...
Sub-access Identifier: current info
Sub-access Identifier:
7. This parameter applies only to TL1 commands/messages.
Type the name (20 characters maximum) of the sub-
access identifier that this channel belongs to, then press
ENTER
. The group of LMS1000 channels monitoring a
sub-entity in an NMA system should have the same
access identifier and sub-access identifier. Only alpha-
numeric characters can be entered for this parameter.
TL1 uses specific values for this parameter. Refer to
TA-NWT-001360, Table 4-1.
8. The system responds with...
Alarm Type: current info
Alarm Type (Y or N):
9. Type
Y
if the alarm condition determined by this channel
is required to be recorded in the alarm log (required if
System Alarm Reporting or TL1 report messaging is
desired for this channel, and/or an alarm class of 1
through 8 is assigned to this channel) when it is activated
and
N
if not, then press
ENTER
.
10. If ”Y” was entered above, the system responds with...
System Alarm Report mode: current info
System Alarm Report mode (Y or N):
11. Type
Y
if the system is required to initiate an alarm report
if this channel alarms and
N
if not, then press
ENTER
.
12. If "Y" was entered above for "Alarm Type", the system
responds with...
Alarm Class Number:
13. Type the desired alarm class number associated with this
channel, then press
ENTER
. Alarm classes are specified
with the numbers 0 through 8, with 0 representing no
alarm class.
14. If ”Y” was entered above for the ALARM TYPE parameter,
the system responds with...
Condition Type: current info
Condition Type:
15. This parameter applies only to TL1 commands/messages.
Type the name (20 characters maximum) which
describes this alarm or event state, then press
ENTER
.
Only alpha characters can be entered for this parameter.
TL1 uses specific values for this parameter. Refer to
TA-NWT-001360 Tables 5-1 through 5-4.
16. The system responds with...
Condition Description: current info
Condition Description:
17. This parameter applies only to TL1 commands/messages.
Type a user-defined text message (40 characters
maximum) which provides a detailed description of this
alarm, event, or condition. Then press
ENTER
. May also
be used to describe any action to be taken as a result of
the condition. All printable ASCII characters are valid
except for the percent sign (%), double quotes ("), and the
backslash (\).
18. If ”Y” was entered above for the ALARM TYPE parameter,
the system responds with...
Notification Code: current info
Notification Code:
19. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes the
severity of this alarm or event condition, then press
ENTER
.
CR - critical alarm NA - not alarmed
MJ - major alarm NR - not reported when event occurs
MN - minor alarm