Installation Manual
NetSure™ LMS Data Processing Unit
Installation Instructions, Section 5879 (Issue BA, April 7, 2014)
Spec. No: 58650500, 586505500 Code: Section 5879
Model No: LMS1000 Issue BA, April 7, 2014
[94 of 149]
22. The system responds with...
Limit 1 Notification Code: current info
Limit 1 Notification Code:
23. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes the
severity of this alarm or event condition, then press
ENTER
.
CR - critical alarm NA - not alarmed
MJ - major alarm NR - not reported when event occurs
MN - minor alarm
24. The system responds with...
Limit 1 Service Effect Code: current
info
Limit 1 Service Effect Code:
25. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes how this
alarm or event affects service, then press
ENTER
.
SA = service-affecting condition, immediate action
required
NSA = nonservice-affecting condition, action required
26. The system responds with...
Alarm Class Number:
27. Type the desired alarm class number associated with the
first alarm limit, then press
ENTER
. Alarm classes are
specified with the numbers 0 through 8, with 0
representing no alarm class.
28. The system responds with...
Condition Type: current info
Condition Type:
29. This parameter applies only to TL1 commands/messages.
Type the name (20 characters maximum) which
describes this alarm or event state, then press
ENTER
.
Only alpha characters can be entered for this parameter.
TL1 uses specific values for this parameter. Refer to
TA-NWT-001360 Tables 5-1 through 5-4.
30. The system responds with...
Condition Description: current info
Condition Description:
31. This parameter applies only to TL1 commands/messages.
Type a user-defined text message (40 characters
maximum) which provides a detailed description of this
alarm, event, or condition. Then press
ENTER
. May also
be used to describe any action to be taken as a result of
the condition. All printable ASCII characters are valid
except for the percent sign (%), double quotes ("), and the
backslash (\).
32. The system responds with...
Limit 2 Enabled: current info
Limit 2 Enabled (Y or N):
33. Type
Y
to enable this alarm limit or
N
to disable this alarm
limit. Then press
ENTER
.
34. The system responds with...
Limit 2 Value: current info
Limit 2 Value:
35. Type the required value of the second alarm setting (5
digits, 99999 maximum), then press
ENTER
.
36. The system responds with...
Limit 2 Type: current info
Limit 2 Type is High or Low (H or L):
37. Type
H
if the second alarm setting is a high limit and
L
if
the second alarm setting is a low limit, then press
ENTER
.
38. The system responds with...
Limit 2 Name: current info
Limit 2 Name:
39. Type the desired name of the second alarm setting (10
characters maximum), then press
ENTER
.
40. The system responds with...
Limit 2 Notification Code: current info
Limit 2 Notification Code:
41. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes the
severity of this alarm or event condition, then press
ENTER
.
CR - critical alarm NA - not alarmed
MJ - major alarm NR - not reported when event occurs
MN - minor alarm
42. The system responds with...
Limit 2 Service Effect Code: current
info
Limit 2 Service Effect Code:
43. This parameter applies only to TL1 commands/messages.
Type one of the following codes which describes how this
alarm or event affects service, then press
ENTER
.
SA = service-affecting condition, immediate action
required
NSA = nonservice-affecting condition, action required
44. The system responds with...
Alarm Class Number:
45. Type the desired alarm class number associated with the
second alarm limit, then press
ENTER
. Alarm classes are