Application Guide

SAG586505000 System Application Guide
SAG586505500 Spec. No. 586505000 (Model LMS1000)
Issue AZ, April 7, 2014 Spec. No. 586505500 (Model LMS1000)
Page 42 of 62
This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy
Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.
2. 586505000/586505500 LMS1000 MAIN CABINET
2.1 Input Ratings
2.1.1 Input Voltage Range: 20 - 60 Volts DC.
2.1.2 Maximum Input Current: 0.7 Amperes.
2.2 Mounting
2.2.1 586505000 List 1: Furnished reversible mounting angles permit mounting in a 19" or 23" wide
relay rack with 1" or 1-3/4" multiple drilling. 586505000 and 586505500 List 2: Furnished
mounting angles permit mounting in a 23" wide relay rack with 1" or 1-3/4" multiple drilling.
2.2.2 Mounting angles may be re-positioned for flush front mounting, 5-inch front projection
mounting, or 6-inch front projection mounting.
2.3 I/O Circuit Card Mounting Positions
2.3.1 Provides for mounting of any combination of I/O (analog, binary, relay, and temperature) circuit
cards. CARDS MUST BE LOADED LEFT TO RIGHT (AS VIEWED FROM THE FRONT OF
THE CABINET). DO NOT SKIP SLOTS.
2.3.2 Contains ten (10) I/O circuit card mounting slots.
2.4 CPU Circuit Card, Part No. 545476 (used in 586505000/586505500) and 545558 (used in
582140000, 582140001, and 582126100)
2.4.1 General: The CPU circuit card contains the system's firmware, a power supply circuit,
communications circuits, and programmable local LED indicators. This circuit card can be
equipped with a piggy-back modem circuit card.
2.4.2 Processor: MC 68EN302 - 20MHz.
2.4.3 SRAM - Data: 2M bytes.
2.4.4 Flash - System: 1M bytes.
2.4.5 Flash - Application: 3M bytes.
2.4.6 Real-Time Clock: The time base for the operating system comes from a real time clock. This
integrated circuit is totally self-contained and does not require any calibration. Accuracy=10
PPM (27 seconds per month) or better at nominal temperature.
2.4.7 Low Lithium Battery Detection Circuit: Illuminates a local LED indicator for low lithium
battery indication.
2.4.8 Communications:
Note: The following ports may be different when the LMS1000 is used in a Spec. No.
582140000, 582140001, or 582126100 Power System. Refer to the 582140000,
582140001, or 582126100 system documentation.
(A) Local Port (RS-232): A front panel 9-pin female D-type jack is provided. This jack is
configured as a DCE (Data Communication Equipment). Refer to Table 1 for pin
assignments.
Note: When List 88 is ordered, the port on the front of the 586505000/586505500 cabinet
is inactive, and the local port is redirected to OEM1 located on the rear of the
cabinet. The configuration of the OEM1 port in this application is as shown in Table
2.
(B) Modem Port: An internal 56K bps modem circuit card can be installed onto the CPU
circuit card. The modem circuit card connects to an RJ-11 phone jack located on the rear
of the system cabinet for customer phone line connection.
(C) Ethernet Port: A rear panel RJ-45 10BaseT jack is provided. This jack has a standard
Ethernet pin configuration scheme, twisted pair.
(D) OEM1 Port (RS-232): A 9-pin female D-type jack is provided on the rear panel of the
586505000/586505500 cabinet. This jack is configured as a DTE (Data Terminal
Equipment). Refer to Table 2 for pin assignments. The port's function is determined by
the LMS1000 Software Options or LMS1000 Specialty Interface Options installed.
Home
Home