Owner`s manual

ManualsBrandsEmerson ManualsBeverage DispenserH-770

Instant Hot Water Dispenser

Owner’s Manual

TranScape

™

View

™

TranScape

™

Wave

™

HC3/GN3

H990

H770

The Emerson logo is a trademark and

service mark of Emerson Electric Co.

1.800.558.5700

www.insinkerator.com

Installation, Care & Use

Instalacion, cuidado & uso

Installation, soin et utilisation

Summary of content (8 pages)

PAGE 1
TranScape View TranScape Wave HC3/GN3 H990 H770 ™ ™ Instant Hot Water Dispenser Owner’s Manual Installation, Care & Use Instalacion, cuidado & uso Installation, soin et utilisation 1.800.558.5700 www.insinkerator.com 44068 REV. A The Emerson logo is a trademark and service mark of Emerson Electric Co. Printed in USA © 2007 InSinkErator, a division of Emerson Electric Co. All Rights Reserved.
PAGE 2
Identify the model of your instant hot water dispenser and record it here:________________ ® We are delighted that you have chosen the InSinkErator® Instant Hot Water Dispenser to be a part of your home. This unique appliance will save you time and effort in the kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser.
PAGE 3
START HERE COMPONENTS IN THIS PACKAGE 1A 3/8" Tube 3/4" Screws (2) Brass Nut / Ferrule / Tube Insert HC-Wave-SS Extension & Star Nut (View & Wave only) Quick Connector Wing Nut Washers HC3-SS 1-5/8" 1-5/8" Rubber Small Steel H-View-SS H-Wave-SS GN3-SS 2-1/4" 2-1/4" Large Steel Fiber Snap-Connect Fitting (3 pieces) Tank Extension & Star Nut (View & Wave only) 1-5/8" 1-5/8" Rubber Small Steel 3/4" Screws (2) Wing Nut 2-1/4" 2-1/4" Semi-Circular Mounting Plate Wing Nut Rubber
PAGE 4
2A INSTALLING THE FAUCET - VIEW/ WAVE / HC3/ GN3 View/Wave/HC3/GN3 ■ Unpack dispenser components. 2A INSTALLING THE FAUCET - H990 H990 ■ Unpack dispenser components. ■ On a firm, flat surface, carefully ■ On a firm, flat surface, carefully straighten the copper tubing. straighten the copper tubing. ■ Remove the wing nut from the valve body. Property Damage: Do not pinch or break copper tubing. Do not distort the last 1 inch of tubing. Property Damage: Do not pinch or break copper tubing.
PAGE 5
2A INSTALLING THE FAUCET - H770 H770 3A MOUNTING THE TANK ■ Select a spot under the sink to mount ■ Unpack dispenser components. Tank must be mounted level to ensure proper operation. ■ On a firm, flat surface, carefully straighten the copper tubing. tank vertically within reach of both plumbing and electrical connections. The tank should be within 16" or less of faucet water lines and within 30" or less of a standard grounded outlet.
PAGE 6
INSTALLING FILTRATION (Optional) A Available as an option; separate purchase required. ■ Mark hole locations for filter head and bracket in a spot that allows for filter replacement. 5A FINAL WATER CONNECTION Brass Nut Ferrule Brass Insert ■ Drill 1/8" starter holes and attach bracket to wall with wood screws, turning until snug. Plastic tube ■ Remove red filter cap, insert filter Personal Injury: Do not locate filter above an outlet or other electrical device.
PAGE 7
CARE AND USE Electric Shock Hazard: Using an ungrounded or improperly connected appliance can result in serious injury or death from electrical shock. This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
PAGE 8
Please read Troubleshooting Guide and/or visit www.insinkerator.com before calling AnswerLine™ View Wave HC3/GN3 H990 H770 ™ TROUBLESHOOTING PROBLEM POSSIBLE CAUSE Water and steam spits forcefully from spout without turning on the dispenser faucet. • Unit is boiling. Water is not hot. • The unit is unplugged. May be normal during initial setup. ™ WHAT TO DO • Activate faucet lever to release some water from the tank. • Adjust water temperature using dial on tank front.