Instruction Manual

Local Interface Flow Chart/Menu Trees
April 2014
Instruction Manual
D103176X012
90
Field Communicator Fast‐Key Sequence (Instrument Level AC)
Function/Variable
Fast‐Key
Sequence
Coordinates
(1)
Analog Input Calibration 1‐3‐1 3‐E
Analog Input Units 1‐2‐2‐1 4‐E
Auto Calibrate Travel 1‐3‐2 3‐E
Auto Setup 1‐1‐1 3‐B
Auto Tuner 1‐1‐1‐3 3‐B
Basic Setup 1‐1 3‐B
Calibrate 1‐3 3‐E
Damping Factor 1‐1‐1‐4‐2 5‐B
Date 1‐2‐1‐4 4‐D
Descriptor 1‐2‐1‐3 4‐D
Detailed Setup 1‐2 3‐D
Device Description Revision 2‐2 2‐F
Device Identification 2‐1‐9 3‐F
Device Information 2‐1 3‐F
Device Revision 2‐1‐2 3‐F
Display 2 1‐E
Enable Integral Control 1‐2‐3‐6‐1 6‐F
Expert Tuning Gains 1‐1‐1‐4‐3 6-C
Firmware Date 2‐1‐4 3‐F
Firmware Revision 2‐1‐3 3‐F
HART Tag 1‐2‐1‐1 4‐D
HART Universal Revision 2‐1‐1 3‐F
Input Characterization 1‐2‐3‐4 4‐F
Input Range High 1‐2‐2‐2 4‐E
Input Range Low 1‐2‐2‐3 4‐E
Instrument Level 2‐1‐8 3‐F
Instrument Mode Hot Key 1‐A
Instrument Serial Number 1‐2‐1‐6 4‐E
Integral Dead Zone 1‐2‐3‐6‐3 6‐F
Function/Variable
Fast‐Key
Sequence
Coordinates
(1)
Integral Gain 1‐2‐3‐6‐2 6‐F
Integral Settings 1‐2‐3‐6 6‐F
LUI Language 1‐2‐1‐8 4‐E
LUI Pressure Units 1‐2‐2‐5 4‐E
Manual Calibrate Travel 1‐3‐3 3‐E
Manual Setup 1‐1‐2 3‐B
Measured Variable 1‐2‐2 4‐E
Main Electronics Revision 2‐1‐5 3‐F
Maximum Supply Pressure 1‐1‐2‐2‐3 5‐C
Message 1‐2‐1‐2 4‐D
Polling Address 1‐2‐1‐7 4‐E
Pressure Units 1‐2‐2‐4 4‐E
Protection Hot Key 1‐A
Secondary Electronics Revision 2‐1‐6 3‐F
Sensor Serial Number 2‐1‐7 3‐F
Setup Wizard 1‐1‐1‐1 3‐B
Switch 1 Closed
(2)
1‐2‐4‐2 4‐G
Switch 1 Trip Point
(2)
1‐2‐4‐1 4‐G
Switch 2 Closed
(2)
1‐2‐4‐4 4‐G
Switch 2 Trip Point
(2)
1‐2‐4‐3 4‐G
Transmitter Action
(2)
1‐2‐4‐5 4‐G
Transmitter Calibration
(2)
1‐3‐4 3‐E
Travel Cutoff High 1‐2‐3‐5‐1 6‐F
Travel Cutoff Low 1‐2‐3‐5‐2 6‐F
Tuning Hot Key 1‐B
Tuning Set 1‐1‐1‐4‐1 5‐B
Valve Serial Number 1‐2‐1‐5 4‐E
Zero Control Signal 1‐1‐2‐2‐4 5‐C
1. Coordinates are to help locate the item on the menu tree on the facing page.
2. Available only if the instrument has a transmitter and limit switches installed.