Instruction Manual
Local Interface Flow Chart/Menu Trees
April 2014
Instruction Manual
D103176X012
88
Field Communicator Fast‐Key Sequence (Instrument Level HC, AD and PD)
Function/Variable
Fast‐Key
Sequence
Coordinates
(1)
Actuator Style 1‐2‐5‐2 4‐E
Alert Record 1‐2‐7‐6 4‐G
Analog Input 2 1‐E
Analog Input Calibration 1‐4‐1 2‐E
Analog Input Range High 1‐2‐4‐2 4‐D
Analog Input Range Low 1‐2‐4‐3 4‐D
Analog Input Units 1‐2‐4‐1 4‐D
Auto Calibrate Travel 1‐4‐2 2‐E
Auto Setup 1‐1‐1 2‐B
Auto Tuner 1‐1‐1‐3 3‐B
Basic Setup 1‐1 2‐B
Burst 1‐2‐1‐5 4‐C
Calibrate 1‐4 2‐E
Control Mode 1‐2‐1‐2 3‐C
Custom Characteristic Table 1‐2‐6‐5 4‐F
Cycle Count 1‐2‐7‐4‐4 6‐H
Cycle Count Alert 1‐2‐7‐4 6‐H
Cycle Count Alert Enable 1‐2‐7‐4‐1 6‐H
Cycle Count Alert Point 1‐2‐7‐4‐2 6‐H
Cycle Count Deadband 1‐2‐7‐4‐3 6‐H
Damping Factor 1‐1‐2‐3‐2 4‐C
Date 1‐2‐3‐4 5‐D
Descriptor 1‐2‐3‐3 5‐D
Device Description Revision 1‐3‐3 2‐F
Device Identification 1‐3‐2‐9 2‐H
Device Information 1‐3‐2 2‐G
Device Revision 1‐3‐2‐2 2‐G
Drive Alert Enable 1‐2‐7‐5‐1 5‐H
Drive Current Fail 1‐2‐8‐4 3-F
Drive Signal 5 1‐E
Enable Integral Control 1‐2‐6‐9‐1 6-G
Expert Tuning Gains 1‐1‐1‐4‐3 5‐B
Failure Alerts 7‐2 1-G
Failure Group Enable 1‐2‐7‐6‐4‐2 6‐I
Firmware Date 1‐3‐2‐4 2‐G
Firmware Revision 1‐3‐2‐3 2‐G
Flash Rom Failure 1‐2‐8‐1 3-E
HART Tag 1‐2‐3‐1 5-D
HART Universal Revision 1‐3‐2‐1 2‐G
Input Characterization 1‐2‐6‐4 4‐F
Instrument Level 1‐3‐2‐8 2‐G
Instrument Mode Hot Key 1‐A
Instrument Serial Number 1‐2‐3‐6 5‐D
Instrument Status 7 1‐E
Integral Dead Zone 1‐2‐6‐9‐3 6‐G
Integral Gain 1‐2‐6‐9‐2 6‐G
Integral Settings 1‐2‐6‐9 6‐G
Limit Switch Stat Enable 1‐2‐7‐6‐4‐3 6‐I
LUI Language 1‐2‐3‐8 5‐D
LUI Pressure Units 1‐2‐4‐5 4‐D
Main Electronics Revision 1‐3‐2‐5 2‐G
Manual Calibrate Travel 1‐4‐3 2‐E
Manual Setup 1‐1‐2 3‐B
Maximum Supply Pressure 1‐2‐5‐1 4‐E
Message 1‐2‐3‐2 5‐D
Minimum Opening Time 1‐2‐6‐8‐1 6-F
Minimum Closing Time 1‐2‐6‐8‐2 6-F
NVM Fail 1‐2‐8‐5 3-F
Operational Status 7‐3 1-G
Function/Variable
Fast‐Key
Sequence
Coordinates
(1)
Polling Address 1‐2‐3‐7 5‐D
Pressure 6 1‐E
Pressure Calibration 1‐4‐4 2‐E
Pressure Sensor Failure 1‐2‐8‐7 3-F
Pressure Units 1‐2‐4‐4 4‐D
Protection Hot Key 1‐A
Reference Voltage Failure 1‐2‐8‐3 3-F
Response Control 1‐2‐6 4‐E
Restart 1‐2‐1‐4 3‐C
Restart Control Mode 1‐2‐1‐3 3‐C
Secondary Electronics Revision 1‐3‐2‐6 2‐G
Self Test Shutdown 1‐2‐8 2‐D
Sensor Serial Number 1‐3‐2‐7 2‐G
Set Point Filter Time 1‐2‐6‐6 4‐F
Setup Wizard 1‐1‐1‐1 3‐B
Stroke Valve 1‐5 1‐D
Switch 1 Closed
(2)
1‐2‐9-2 3-E
Switch 1 Trip Point
(2)
1‐2‐9‐1 3-D
Switch 2 Closed
(2)
1‐2‐9‐4 3-E
Switch 2 Trip Point
(2)
1‐2‐9‐3 3-E
Temperature 1‐3‐1‐1 3‐G
Temperature Comp Fail 1‐2‐8‐2 3-F
Temperature Sensor Failure 1‐2‐8‐6 3-F
Temperature Units 1‐2‐4‐6 4‐D
Transmitter Action
(2)
1‐2‐9‐5 3-E
Transmitter Calibration
(2)
1‐4‐6 2‐E
Travel 3 1‐E
Travel Accumulator 1‐2‐7‐3‐4 5‐H
Travel Accumulator Alert Enable 1‐2‐7‐3‐1 5‐G
Travel Accumulator Alert Point 1‐2‐7‐3‐2 5‐G
Travel Accumulator Dead Band 1‐2‐7‐3‐3 5‐G
Travel Alert Deadband 1‐2‐7‐1‐7 5‐G
Travel Alert High Point 1‐2‐7‐1‐3 5‐G
Travel Alert High High Point 1‐2‐7‐1‐5 5‐G
Travel Alert Low Point 1‐2‐7‐1‐4 5‐G
Travel Alert Low Low Point 1‐2‐7‐1‐6 5‐G
Travel Cutoff Low 1‐2‐6‐7‐4 6-F
Travel Cutoff High 1‐2‐6‐7‐3 6-F
Travel Deviation Alert Enable 1‐2‐7‐2‐1 6‐G
Travel Deviation Alert Point 1‐2‐7‐2‐2 6‐G
Travel Deviation Time 1‐2‐7‐2‐3 6‐G
Travel High / Low Enable 1‐2‐7‐1‐1 5‐F
Travel High High / Low Low Enable 1‐2‐7‐1‐2 5‐F
Travel Limit High 1‐2‐6‐7‐1 6‐E
Travel Limit Low 1‐2‐6‐7‐2 6-F
Travel Sensor Failure 1‐2‐8‐8 3-F
Travel Setpoint 4 1‐E
Tuning Hot Key 1‐B
Tuning Set 1‐1‐2‐3‐1 4‐C
Valve Group Enable 1‐2‐7‐6‐4‐1 6‐I
Valve Style 1‐2‐5‐3 4‐E
Valve Serial Number 1‐2‐3‐5 5‐D
Zero Control Signal 1‐2‐5‐4 4‐E
1. Coordinates are to help locate the item on the menu tree on the facing page.
2. Available only if the instrument has a transmitter and limit switches installed.