Instruction Manual EW Valve D100399X012 September 2014 Fisherr EWD, EWS, and EWT Valves through NPS 12x8 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Educational Services . . . . . . . . . . . . . . . . . . . . . . . . .
Instruction Manual EW Valve D100399X012 September 2014 Table 1. Specifications End Connection Styles Flanged Ends: CL300, CL600, or CL900 Raised-face or ring-type joint flanges per ASME B16.5 Buttwelding Ends: Styles per ASME B16.25 schedules consistent with ASME B16.34 are: Schedules J 40 or J 80 for all CL300 and CL600 valves, Schedule J 80 or J XXS for NPS 8x6 CL900 valves, or Schedule J 80, J 100, or J 120 for NPS 12x8 CL900 valves.
Instruction Manual D100399X012 EW Valve September 2014 Figure 2. Cutaway Detail of the Fisher WhisperFlo Trim, Valve Body Typical W6825-1 Description These single-port globe-style valves have cage guiding, clamped seat rings, and push-down-to-close valve plug action. Valve configurations are as follows: EWD: Balanced valve plug with metal-to-metal seating for all general applications over a wide range of pressure drops and temperatures.
Instruction Manual EW Valve D100399X012 September 2014 Table 2.
Instruction Manual EW Valve D100399X012 September 2014 Check with your process or safety engineer for any additional measures that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual. CAUTION When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature, pressure drop and controlled fluid conditions.
EW Valve Instruction Manual September 2014 D100399X012 4. Use accepted piping and welding practices when installing the valve in the line. For flanged valve bodies, use a suitable gasket between the valve body and pipeline flanges. CAUTION Depending on valve body materials used, post weld heat treating may be required. If so, damage to internal elastomeric and plastic parts, as well as internal metal parts is possible. Shrink-fit pieces and threaded connections may also loosen.
Instruction Manual D100399X012 EW Valve September 2014 2. Provide adequate support to the bonnet while removing the bonnet nuts. 3. Be aware that the bonnet/plug/cage may tip over as they are lowered from the valve body. Make provision to prevent tipping. 4. Be aware that the cage and seat ring may not come out with the bonnet and plug/stem assembly. If this occurs, make provision to support these parts, as they may fall out unexpectedly. Assembly 1. 2. 3. 4.
Instruction Manual EW Valve D100399X012 September 2014 Note Whenever a gasket seal is disturbed by removing or shifting gasketed parts, install a new gasket upon reassembly. This is necessary to ensure a good gasket seal because the used gasket may not seal properly. Figure 3. Lubricator and Lubricator/Isolating Valve (optional) LUBRICATOR 10A9421-A AJ5428-D A0832-2 LUBRICATOR/ISOLATING VALVE Packing Lubrication CAUTION Do not lubricate graphite packing. Graphite packing is self-lubricated.
Instruction Manual EW Valve D100399X012 September 2014 Figure 4.
Instruction Manual EW Valve D100399X012 September 2014 Packing Maintenance Note For valves with ENVIRO-SEAL live-loaded packing, see the Fisher instruction manual, ENVIRO-SEAL Packing System for Sliding-Stem Valves, D101642X012, for packing instructions. For valves with HIGH-SEAL live-loaded packing, see the Fisher instruction manual, HIGH-SEAL Live-Loaded Packing System, D101453X012, for packing instructions.
Instruction Manual D100399X012 EW Valve September 2014 D Do not remove the actuator from the valve while the valve is still pressurized. D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal injury. D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the actuator cannot suddenly open or close the valve.
Instruction Manual EW Valve D100399X012 September 2014 6. Remove the locknut and separate the valve plug and stem from the bonnet. Set the parts on a protective surface to prevent damage to gasket or seating surfaces. 7. Remove the bonnet gasket (key 10, figure 22 through 24), and cover the opening in the valve body to protect the gasket surface and prevent foreign material from getting into the valve body cavity. 8.
Instruction Manual D100399X012 EW Valve September 2014 Note Proper performance of the tightening procedures in step 11 compresses the spiral wound gasket (key 12, figure 22 through 23) or load ring (key 26, figure 24) enough to both load and seal the seat ring gasket (key 13, figure 22, 23 or 24). It also compresses the outer edge of the bonnet gasket (key 10, figure 22 through 24) enough to seal the body-to-bonnet joint.
Instruction Manual EW Valve D100399X012 September 2014 Trim Maintenance WARNING Avoid personal injury or property damage from sudden release of process pressure. Before performing any maintenance operations: D Do not remove the actuator from the valve while the valve is still pressurized. D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal injury.
Instruction Manual D100399X012 EW Valve September 2014 CAUTION In the following applicable procedures, to avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud. For C-seal construction, see the appropriate C-seal sections in this instruction manual.
Instruction Manual EW Valve D100399X012 September 2014 Figure 7. TSO (Tight Shutoff Trim), Detail of Protected Soft Seat OUTER PLUG INNER PLUG CAGE PROTECTED SOFT SEAT SEAT RING A7088 7. For constructions other than TSO (tight shutoff trim), remove the seat ring (key 9) or disk seat (key 22), seat ring gasket (key 13), and the seat ring adaptor (key 5) and adaptor gasket (key 14) where used in a restricted-capacity construction.
Instruction Manual EW Valve D100399X012 September 2014 Figure 8. Typical Balanced TSO Trim VALVE PLUG SEAL A7096 PROTECTED SOFT SEAT Except with respect to the ENVIRO-SEAL Bellows Seal Bonnet assembly, with metal seat constructions, seating surfaces of the valve plug and seat ring (keys 2 and 9, figures 24 through 26) can be lapped for improved shutoff. (Deep nicks should be machined out rather than ground out.) Use a good quality lapping compound of a mixture of 280 to 600-grit.
EW Valve September 2014 Instruction Manual D100399X012 For the EWD carbon-filled PTFE piston ring, the ring is split in one place. If there is visible damage, spread the ring slightly, and remove it from the groove in the valve plug. To install a carbon-filled PTFE piston ring, spread the ring apart slightly at the split, and install it over the stem and into the groove in the valve plug. The open side must face along the stem, depending on flow direction, as shown in figure 22.
Instruction Manual EW Valve D100399X012 September 2014 3. To replace the adaptor (key 24, figure 21) on ENVIRO-SEAL bellows seal bonnets, place the plug stem assembly and valve plug in a soft-jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface. Drive out the pin (key 36, figure 21). Reverse the plug stem assembly and valve plug in the soft-jaw chuck or vise.
EW Valve Instruction Manual September 2014 D100399X012 D Assemble the piston ring, anti-extrusion rings, backup ring, and retainer. 6. For all constructions, place the gaskets (keys 12, 11 or 14 if used, and 10) and the shim, if used (key 53), on top of the cage or cage retainer. If there is a cage adaptor (key 4) or a bonnet spacer (key 32), set it on the cage or cage retainer gaskets and place another flat sheet gasket (key 10) on top of the adapter or spacer.
Instruction Manual EW Valve D100399X012 September 2014 Figure 9. Fisher EWD with C-seal Trim 64 FLOW DOWN 64 FLOW UP VIEW A 7 8 65 64 A 2 A6790 9 6. Install the new plug/retainer assembly with C-seal plug seal on the new stem following the appropriate instructions in the Trim Replacement section of this manual. 7. Install piston rings by following instructions in the Trim Replacement section of this manual. 8.
Instruction Manual EW Valve D100399X012 September 2014 FOR VALVE PLUGS FITTING PORT SIZE (Inches) DIMENSIONS, mm (See Drawing Below) Part Number (To Order A Tool) A B C D E F G H 82.55 52.324 52.578 4.978 - 5.029 3.708 - 3.759 41.148 52.680 52.781 55.118 55.626 70.891 - 71.044 24B9816X012 3.4375 101.6 58.674 58.928 4.978 - 5.029 3.708 - 3.759 50.8 61.011 61.112 63.449 63.957 85.166 - 85.319 24B5612X012 3.625 104.394 65.024 65.278 4.978 - 5.029 3.708 - 3.759 50.8 68.
Instruction Manual EW Valve D100399X012 September 2014 Figure 11. Installing the C-seal Plug Seal Using the Installation Tool INSTALLATION TOOL C-SEAL METAL PLUG SEAL VALVE PLUG HORIZONTAL REFERENCE SURFACE FLOW DOWN A6778 NOTE: PRESS INSTALLATION TOOL OVER VALVE PLUG UNTIL THE TOOL CONTACTS THE HORIZONTAL REFERENCE SURFACE OF THE VALVE PLUG. Figure 12.
EW Valve Instruction Manual September 2014 D100399X012 CAUTION To avoid excessive leakage and seat erosion, the valve plug must be initially seated with sufficient force to overcome the resistance of the C-seal plug seal and contact the seat ring. You can correctly seat the valve plug by applying the full actuator load. This force will adequately drive the valve plug to the seat ring, thus giving the C-seal plug seal a predetermined permanent set.
Instruction Manual EW Valve D100399X012 September 2014 Figure 13. Lower (Valve Plug to Seat Ring) and Upper (C-seal Plug Seal to Cage) Seating Surfaces RETAINER C-seal METAL PLUG SEAL 1 VALVE PLUG CAGE UPPER SEATING SURFACE CAGE PLUG NOTE: 1 UPPER SEATING SURFACE IS THE AREA OF CONTACT BETWEEN THE C-seal METAL PLUG SEAL AND THE CAGE. SEAT RING LOWER SEATING SURFACE A6780 8.
Instruction Manual EW Valve D100399X012 September 2014 Figure 14. Example of Machining the Lower (Valve Plug to Seat Ring) and Upper (C-seal Plug Seal to Cage) Seating Surfaces C-seal RETAINER UPPER SEATING SURFACE 0.508 (0.020)(4) 3 MACHINING OF THE UPPER SEATING SURFACE MUST EQUAL THE TOTAL MACHINING OF THE LOWER SEATING SURFACE (PLUG PLUS SEAT RING). IF NOT, THE RETAINER MAY STRIKE THE UPPER SEATING SURFACE BEFORE THE VALVE PLUG PROPERLY SEATS ON THE LOWER SEATING SURFACE. PLUG 1 0.254 (0.
Instruction Manual EW Valve D100399X012 September 2014 3. Place the C-seal plug seal over the top of the valve plug and press it onto the plug using the installation tool. Carefully press the C-seal plug seal onto the plug until the installation tool contacts the horizontal reference surface of the valve plug (figure 11). 4. Apply a suitable high-temperature lubricant to the threads on the plug.
EW Valve September 2014 Instruction Manual D100399X012 4. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new ENVIRO-SEAL stem/bellows assembly. To remove the existing valve plug from the stem, first, place the existing plug stem assembly in a soft-jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface. Drive out or drill out the pin (key 8). 5.
Instruction Manual EW Valve D100399X012 September 2014 Figure 15. PTFE Packing Arrangement for Use in Fisher ENVIRO-SEAL Bellows Seal Bonnets UPPER WIPER (KEY 12) BUSHING (KEY 13) FEMALE ADAPTOR PACKING RING MALE ADAPTOR PACKING SET (KEY 6) SPACER (KEY 8) SPACER (KEY 8) THRUST RING (KEY 39) SPRING (KEY 8) 12B4182- A/IL 9.5 mm (3/8 INCH) STEM A5855/IL THRUST RING (KEY 39) SPACER (KEY 8) 12B4185- A- SHT1/IL 12.7 mm (1/2 INCH) STEM 12B4182- A- SHT2/IL 12B4185- A- SHT2/IL 9.
Instruction Manual EW Valve D100399X012 September 2014 Note Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easy comparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product. WARNING Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used.
Instruction Manual D100399X012 EW Valve September 2014 15. Install the travel indicator parts and stem locknuts; mount the actuator on the valve body according to the procedure in the appropriate actuator instruction manual. Replacement of an Installed ENVIRO-SEAL Bellows Seal Bonnet (Stem/Bellows Assembly) 1. Remove the actuator and bonnet according to steps 1 through 6 of the Replacing Packing procedure of the Maintenance section. 2. Lift out the cage.
EW Valve September 2014 Instruction Manual D100399X012 D Thread the adaptor into the valve plug and tighten to the appropriate torque value. 7. Complete the installation by following steps 7 through 15 of the ENVIRO-SEAL Bellows Seal Bonnet installation instructions given above. Purging the ENVIRO-SEAL Bellows Seal Bonnet The ENVIRO-SEAL bellows seal bonnet has been designed so that it can be purged or leak tested. Refer to figure 21 for an illustration of an ENVIRO-SEAL bellows seal bonnet.
Instruction Manual EW Valve D100399X012 September 2014 Parts Kits Gasket Kits Gasket Kits (includes keys 10, 12, 13, and 53; plus 11 and 14 for restricted trim) VALVE SIZE, NPS Standard Trim Cage Whisper Trim I Cage Cavitrol III - 1 Stage Cage -198 to 593_C (-325 to 1100_F) Cavitrol III - 2 Stage Cage Whisper Trim III Cage WhisperFlo Cage -198 to 593_C (-325 to 1100_F) Part Number Part Number 4x2 RGASKETX182 RGASKETX442 6x4x2-1/2 RGASKETX282 --- 6x4 or 8x4 RGASKETX212 RGASKETX472 8x6 or 12
Instruction Manual EW Valve D100399X012 September 2014 HIGH-SEAL and ENVIRO-SEAL Packing Retrofit Kits Retrofit kits include parts to convert valves with existing standard bonnets to the HIGH-SEAL or ENVIRO-SEAL packing box construction. Refer to figure 17 for key numbers for HIGH-SEAL packing. For ENVIRO-SEAL packing, refer to figure 18 for PTFE packing key numbers, figure 19 for Graphite ULF packing key numbers, and figure 20 for duplex packing key numbers.
Instruction Manual EW Valve D100399X012 September 2014 Figure 17. Typical Fisher HIGH-SEAL Packing System STUD (KEY 200) HEX NUT (KEY 212) SCREW (KEY 204) PACKING FLANGE (KEY 201) SPRING (KEY 202) LOAD SCALE (KEY 205) INDICATOR DISK (KEY 206) PACKING FOLLOWER (KEY 203) GUIDE BUSHING (KEY 207) GUIDE BUSHING (KEY 208) PACKING RING (KEY 209) GRAPHITE RIBBON PACKING RING (KEY 210) PACKING BOX RING (KEY 211) Figure 19.
Instruction Manual EW Valve D100399X012 September 2014 Parts List Numerous available combinations of valve parts make selection of some parts difficult; when ordering valve parts for which a part number is not listed, provide the valve serial number with the order, permitting proper selection of replacement parts to be made at the factory. Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson Process Management sales office.
Instruction Manual EW Valve D100399X012 Key 16 20* 20* September 2014 Description Part Number S31600 for chrome moly steel or 316 SST bonnet ENVIRO-SEAL bellows seal pipe plug (2 req'd) ENVIRO-SEAL bellows seal stem/bellows assembly 1 ply bellows S31603 (316L SST) trim, N06625 bellows Size 4x2 w/ 12.7 mm (1/2 inch) stem Size 6x4x2-1/2, 6x4, & 8x4 w/ 12.7 mm (1/2 inch) stem N06022 trim, N06022 bellows Size 4x2 w/ 12.7 mm (1/2 inch) stem Size 6x4x2-1/2, 6x4, & 8x4 w/ 12.
Instruction Manual EW Valve D100399X012 September 2014 Figure 21.
Instruction Manual EW Valve D100399X012 September 2014 Valve Body (figures 22 through 24) Note This parts list provides part numbers for standard valves and valves with Whisper Trim I cages only. For part numbers for valves with WhisperFlo, Whisper Trim III, or Cavitrol III cages, contact your Emerson Process Management sales office. Key 1 2* 3* 4 5 6* Description Part Number Valve Body If you need a valve body as a replacement part, order by valve size, serial number, and desired material.
Instruction Manual EW Valve D100399X012 September 2014 Figure 22.
Instruction Manual EW Valve D100399X012 Key 17 18 19 21* 22* 23* 26 27* 28* Description September 2014 Part Number Pipe Plug for drain-tapped valve Flow Arrow, SST Drive screw, SST (6 req'd) Disk Retainer for PTFE-seat EWS or EWT Size 4x2 valve, S31600 1V710835072 Size 6x4x2-1/2 valve, S31600 1V710935072 Size 6x4 or 8x4 valve, CF8M 1V711533092 Size 8x6 or 12x6 valve, CF8M For all except Whisper Trim III cages 1V711833092 Size 10x8 or 12x8 valve CF8M 10A4466X012 R30006 (Alloy 6) 10A4466X022 Disk S
Instruction Manual EW Valve D100399X012 September 2014 Figure 23.
Instruction Manual EW Valve D100399X012 September 2014 Figure 24. Typical Fisher EWT Valve Assemblies FLOW DIRECTION WHISPER TRIM VIEW A FLOW UP 43A8590-B STD TRIM CAVITROL TRIM VIEW A FLOW DOWN CORRECT SPRING-LOADED SEAL RING ORIENTATION 43A8590-B 47.6 TO 136.5 mm (1.875 TO 5.
Instruction Manual EW Valve D100399X012 September 2014 Figure 25.
Instruction Manual EW Valve D100399X012 September 2014 Figure 26. NPS 4x2 Through 12x8 Fisher Valves with 1-Stage Cavitrol III Cage FLOW DIRECTION 58A1012-B 54A8146-B VIEW A NPS 4x2 THROUGH 8x4 VALVES VIEW A NPS 8x6 THROUGH 12x6 VALVES VIEW A APPLY LUB 58A1012-B NPS 4x2 THROUGH 12x6 VALVES WITH OPTIONAL DRAIN PLUG 58A1015-A NPS 12x8 VALVE NOTES: 1 NOT REQUIRED ON NPS 8x6 AND 12x6 VALVES. 2 KEYS 2, 7, & 8 ARE SUPPLIED AS AN ASSEMBLY (KEY 2) FOR NPS 8x6 AND 12x6 VALVES.
Instruction Manual EW Valve D100399X012 September 2014 Figure 27.
Instruction Manual EW Valve D100399X012 September 2014 Figure 28.
Instruction Manual EW Valve D100399X012 September 2014 Figure 29.
Instruction Manual EW Valve D100399X012 September 2014 Key 2* Fisher EWD Valve Plug VALVE SIZE, NPS 4x2 (for 1 piston ring only) 6 x 4 x 2-1/2 (for 1 piston ring only) For 1 piston ring 6 x 4 or 8 x 4 For 3 piston rings 8 x 6 or 12 x 6, except for Whisper Trim III cages 51 or 76 mm (2 or 3 inch) travel For 1 piston ring For 3 piston rings For 1 piston ring 10 x 8 or 12 x 8 For 2 piston rings MATERIAL STEM DIA, mm (INCH) 12.7 (1/2) 19.
Instruction Manual EW Valve D100399X012 September 2014 Key 2* Fisher EWS Valve Plug VALVE SIZE, NPS 4x2 6 x 4 x 2-1/2 6 x 4 or 8 x 4 8 x 6 or 12 x 6 Except for Whisper Trim III cages 10 x 8 or 12 x 8 MATERIAL STEM DIA, mm (INCH) 12.7 (1/2) 19.1 (3/4) 25.4 (1) 31.
Instruction Manual EW Valve D100399X012 September 2014 Key 2* Valve Plug for Fisher EWT with Two-Piece Seal Ring VALVE SIZE, NPS 4x2 MATERIAL 19.1 (3/4) 25.4 (1) 31.
Instruction Manual EW Valve D100399X012 September 2014 C-seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*) VALVE SIZE PORT DIA TRAVEL NPS Inch Inch TRIM STEM DIA mm (Inch) 12.7 (1/2) 1 19.1 (3/4) 25.4 (1) 12.7 (1/2) 6X4 4.375 2 3H 19.1 (3/4) 25.4 (1) 12.7 (1/2) 37H 19.1 (3/4) 25.4 (1) 12.7 (1/2) 1 19.1 (3/4) 25.4 (1) 8X4 4.375 2 12.7 (1/2) 3H 19.1 (3/4) 25.
Instruction Manual EW Valve D100399X012 September 2014 C-seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*) (continued) VALVE SIZE PORT DIA TRAVEL NPS Inch Inch TRIM STEM DIA mm (Inch) 12.7 (1/2) 8X4 4.375 2 37H 19.1 (3/4) 25.4 (1) 19.1 (3/4) 1 25.4 (1) 19.1 (3/4) 8X6 7 2 3H 25.4 (1) 19.1 (3/4) 37H 25.4 (1) 19.1 (3/4) 1 25.4 (1) 19.1 (3/4) 12X6 7 2 3H 25.4 (1) 19.1 (3/4) 37H 25.
Instruction Manual EW Valve D100399X012 September 2014 C-seal Parts for Fisher EWD Valve (Keys 3*, 2*, 9*, 64*, 6*, and 7*) (continued) VALVE SIZE PORT DIA TRAVEL NPS Inch Inch TRIM 3 1 2 3.5(3) 10X8 8 1 2 3.5(3) 3 3H 3 10X8 8 37H 2 3.5(3) 2 3.
Instruction Manual EW Valve D100399X012 September 2014 Key 3* Cage (except for Whisper Trim III and Cavitrol III constructions) Valve Size, NPS 4x2 6x4x2-1/2 6x4 or 8x4 8x6 or 12x6, except for Whisper Trim III cages 10x8 or 12x8 Standard Stainless Steel(1) Cage Style CF8M (316 SST), Electroless Nickel Coating R30006 (Alloy 6) Quick-opening 2U223433272 2U740448932 2U223439102 Equal percentage 2U223733272 2U741048932 2U223739102 Linear 2U224033272 2U741648932 2U224039102 Whisper Trim
Instruction Manual EW Valve D100399X012 September 2014 Key 7* Valve Stem (except for Cavitrol III constructions) BONNET STEM DIA VALVE SIZE, NPS 4x2 6x4x2-1/2 6x4 or 8x4 8x6 CL300 or CL600, except for Whisper Trim III cages 8x6 CL900 51 mm (2-Inch) travel 76 mm (3-Inch) travel 102 mm (4-Inch) travel 51 mm (2-Inch) travel 76 mm (3-Inch) travel 12x6 except for Whisper Trim III cages 10x8 51 or 76 mm (2 or 3-Inch) travel ACTUATOR GROUP Plain Style 1 Extension S31600 (316 SST) S31600 Cr Pl(1
Instruction Manual EW Valve D100399X012 September 2014 Key 7* Valve Stem (except for Cavitrol III constructions) (continued) BONNET STEM DIA VALVE SIZE, NPS 12x8, CL300 or CL600 12x8, CL900 51 mm (2-Inch) travel 76 mm (3-Inch) travel 51 mm (2-Inch) travel 76 mm (3-Inch) travel 1. 2. 3. 4.
Instruction Manual EW Valve D100399X012 September 2014 Keys 10*, 11*, 12*, 13*, 14*, and 53* Gaskets and Shims 58 Standard Trim Cage Whisper Trim I Cage Cavitrol III - 1 Stage Cage -198 to 593_C (-325 to 1100_F) Cavitrol III - 2 Stage Cage Whisper Trim III Cage WhisperFlo Cage -198 to 593_C (-325 to 1100_F) Valve Size, NPS Key Number Part Number Part Number 4x2 Set 10 12 13 53 RGASKETX182 1R3299X0042 1R329799442 1R3296X0042 16A1938X012 RGASKETX442 1R3299X0042 (qty 2) 1R329799442 1R3296X0042 1
Instruction Manual D100399X012 EW Valve September 2014 59
EW Valve September 2014 Instruction Manual D100399X012 Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
