Instruction Manual

Instruction Manual
D103298X012
Control-Disk Valve
May 2011
3
Table 2. Valve Size, Shaft Diameter, and Approximate Weight
VALVE SIZE PRESSURE RATING SHAFT DIAMETER
APPROXIMATE WEIGHT
Wafer‐Style Single‐Flange
DN NPS EN ASME mm Inches kg Pounds kg Pounds
50 2 PN10‐40 CL150/300 12.7 1/2 4.7 10 6.7 15
80 3 PN10‐40 CL150/300 15.9 5/8 7.5 17 11.2 25
100 4 PN10‐40 CL150/300 19.1 3/4 12.5 28 17.6 39
150 6 PN10‐40 CL150/300 25.4 1 15.7 35 26.5 58
200 8
PN10‐16 CL150 31.8 1‐1/4 30.2 67 40.2 89
PN25‐40 CL300 31.8 1‐1/4 33.9 75 46.0 102
250 10
PN10‐16 CL150 31.8 1‐1/4 38.9 86 50.5 111
PN25‐40 CL300 31.8 1‐1/4 51.8 114 79.2 175
300 12
PN10‐16 CL150 38.1 1‐1/2 68.7 151 98.3 217
PN25‐40 CL300 38.1 1‐1/2 76.6 169 104.6 231
Table 3. Material Temperature Capabilities
MATERIAL TEMPERATURE LIMITS
(1)
EN Materials
Valve Body Shaft Bearing Lining and Jacket Seal Packing _C _F
1.0619 Steel S17400 or
S20910
PEEK / PTFE
PTFE or RPTFE PTFE or Graphite –10 to 232 14 to 450
UHMWPE PTFE or Graphite –10 to 93 14 to 200
Metal PTFE or Graphite –10 to 232 14 to 450
R30006 (Alloy 6) or S31600
Nitride
Metal Graphite –10 to 400
(2)
14 to 752
(2)
1.4409
Stainless
Steel
S20910 PEEK / PTFE
PTFE or RPTFE PTFE or Graphite –10 to 232 14 to 450
UHMWPE PTFE or Graphite –10 to 93 14 to 200
Metal PTFE or Graphite –10 to 232 14 to 450
R30006 (Alloy 6) or S31600
Nitride
Metal Graphite –10 to 500
(2)
14 to 932
(2)
CW2M N10276 PEEK / PTFE PTFE or RPTFE PTFE –10 to 232 14 to 450
M35‐2 N05500 PEEK / PTFE PTFE or RPTFE PTFE –10 to 232 14 to 450
ASME Materials
Valve Body Shaft Bearing Lining and Jacket Seal Packing _C _F
WCC steel S17400 or
S20910
PEEK / PTFE
PTFE or RPTFE PTFE or Graphite –29 to 232 -20 to 450
UHMWPE PTFE or Graphite –18 to 93 0 to 200
Metal PTFE or Graphite –29 to 232 -20 to 450
R30006 (Alloy 6) or S31600
Nitride
Metal Graphite –29 to 427
(2)
-20 to 800
(2)
CF3M
Stainless
Steel
S20910 PEEK / PTFE
PTFE or RPTFE PTFE or Graphite –46 to 232 –50 to 450
UHMWPE PTFE or Graphite –18 to 93 0 to 200
Metal PTFE or Graphite –46 to 232 –50 to 450
R30006 (Alloy 6) or S31600
Nitride
Metal Graphite –46 to 454
(2)
–50 to 850
(2)
CW2M N10276 PEEK / PTFE PTFE or RPTFE PTFE –46 to 232 –50 to 450
M35‐2 N05500 PEEK / PTFE PTFE or RPTFE PTFE –46 to 232 –50 to 450
1. Minimum allowable temperature for PN series flanges is -10_C (14_F). See requirements of EN 13445‐2 Annex B for applications below -10_C (14_F) with PN series flanges.
2. For applications exceeding 316_C (600_F), consult your Emerson Process Management sales office for appropriate disk material selection.