Surge Protection TM For Business-Critical Continuity Communications/Data/Signal Line Surge Protection Product Catalog
Mission-Critical Voice and Data Signal Protection Unmatched Protection for Peace of Mind … Think of the investment your company has made in sophisticated communications systems. Now think how costly it would be to your company if this mission-critical equipment went down. The fact is — in a nanosecond — power surges, spikes and transients can compromise or totally disrupt voice and data communications, costing thousands in repairs and lost productivity.
Table of Contents Products Page # TRANSIENT VOLTAGE SURGE SUPPRESSION PowerSure™ DMK Series 2 PowerSure™ — IH Series 3 PowerSure™ — LPM/IM Series 4 PowerSure — LPL/IL Series 5 PowerSure™ — Ordering Information 6 Islatrol — SP-6TVN 7 PowerSure EMC Series 8 PowerSure™ TCS-HW Series 9 ™ ™ ™ Islatrol — RM Series ™ 10 The IEEE Emerald Book recommends that a listed surge protection device (SPD) be installed at the service DATA/SIGNAL LINE PROTECTION Edco RM-CAT6 Series 11 entrance of all
Transient Voltage Surge Suppression PowerSure® DMK Series Surge Suppression for AC Applications The PowerSure® DMK Series of Transient Voltage Surge Suppressors (TVSS) provides fast, reliable protection for AC circuits. A small footprint allows easy installation in almost any environment. Install at your critical distribution panel to protect all down-line equipment.
Transient Voltage Surge Suppression PowerSure® — IH Series Modular Surge Protective Device (SPD) capable of handling the high-impulse, potentially damaging transients commonly found at the service entrance or distribution panels. Its robust design allows for placement and protection in the most severe exposure locations.
Transient Voltage Surge Suppression PowerSure® — LPM/IM Series A compact Surge Protective Device (SPD) designed to protect electronic equipment and microprocessor-based systems from transients on distribution and sub-distribution panels, or any medium exposure locations.
Transient Voltage Surge Suppression PowerSure® — LPL/IL Series Electronic grade Surge Protective Device (SPD) designed to protect electronic equipment and microprocessor-based systems from transients on sub-distribution panels, branch panels, or equipment located in low exposure locations.
Transient Voltage Surge Suppression PowerSure® — Ordering Information How To Specify the Appropriate Model All model numbers begin with a prefix (IH, IM, IL). Moving from left to right, choose correct configuration from each column for your application.
Transient Voltage Surge Suppression Islatrol® — SP-6TVN Industrial Strength Surge Suppression (Series) The Islatrol® SP-6TVN is an industrial-strength surge suppression/filtering device that plugs into a standard duplex receptacle. It features uniquely designed repositionable outlets for easy installation behind desks and other furniture.
Transient Voltage Surge Suppression PowerSure® EMC Series 120/240 VAC Heavy Duty (Parallel) The PowerSure® EMC Series surge suppressor is designed to protect AC distribution panel circuits or 120 V power supplies feeding sensitive electronic equipment. Electrically, the unit incorporates MOV and thermal fusing technology. The PowerSure® EMC Series is designed to be installed in parallel on standard single or split phase 120/240 VAC circuits.
Transient Voltage Surge Suppression PowerSure® TCS-HW Series Point-of-Application Protection Utilizing bipolar Silicon Avalanche Diode (SAD) technology, the PowerSure® TCS-HW Series features a two-stage design that provides superior protection for sensitive equipment and for ANSI/IEEE C62.41 Location Category A applications. The PowerSure® TCS-HW Series can be incorporated into larger power protection or used as point-of-application protection.
Transient Voltage Surge Suppression Islatrol® — RM Series 120 VAC Rackmount This line of AC surge protectors is ideal for protecting the power feeding valuable rack equipment. All models provide ten protected outlets on the back and two protected convenience outlets on the front. This series provides 40,000 Amps of surge protection and up to 60 dB of highfrequency noise filtering.
Data/Signal Line Protection Edco RM-CAT6 Series CAT6 Channel Rackmount The Edco RM-CAT6 is a 16-channel high-speed data line protector that utilizes a three-stage hybrid design technology. This unit addresses high-energy voltage transients that can damage expensive computer equipment. Ideal for network switches and hubs, the Edco RM-CAT6 is easily mounted in close proximity to the protected equipment.
Data/Signal Line Protection Edco PLP-S Series Isolated Power Loop Circuit Protection Using the highest quality Silicon Avalanche Diode (SAD) technology, the Edco PLP-S Series is designed to protect your equipment from harmful power surges and transients. Nondegrading SADs will last the lifetime of your equipment, ensuring system uptime.
Data/Signal Line Protection Edco FAS-1 and FAS-2 Series One and Two Pair Signal Line Protector (Commercial) The Edco FAS-1 and Edco FAS-2 Series are multi-stage single pair or two pair surge suppressors designed for high exposure applications. These products were specifically designed to meet multiple low voltage protection applications in the fire and security industries.
Data/Signal Line Protection Edco PHC Series Two-Pair Signaling Circuit Protector (Modular) The Edco PHC Series is designed to protect two pairs of wires specifically for alarm and security systems where operating currents can be as high as 5 Amps. Electrically, the Edco PHC Series is a rugged series hybrid implementing a staged complement of MOVs, copper wound inductors and Silicon Avalanche Diodes. This design reduces series resistance to 0.2 Ohms per pair.
Data/Signal Line Protection Edco RJA-RJD Series RJ-45 Telephone/Data The Edco RJA and Edco RJD Series are four pair telephone/data line protectors that implement advanced two stage hybrid design. These units address over voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology, which consists of solid state resettable fuses. The Edco RJA and Edco RJD Series incorporate Edco RJ-45 female jacks in and out. The Edco RJA voltage clamp is set for C.O.
Data/Signal Line Protection Edco H Series Telecom/Punch Block Protection Advanced Ultra High Speed Technology The Edco H-Series modules are ultra high speed fused solid state secondary protectors for KEY/PABX systems. The units are available in three different clamping voltages. The Edco H-Series is constructed with solid state silicon foldback technology, polyswitch resettable fuses — PTCs — and failure fuses.
Data/Signal Line Protection Edco COHP Series Data/Signal Line/Punch Block Protection High Exposure Applications The Edco COHP modules are three-stage hybrid protectors for low voltage data and telecommunications applications. The modules address over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). Intended to be used on pairs without the presence of ringing voltage.
E
Data/Signal Line Protection Edco MGB Ground Rail Fits Standard 66M1-50 Punch Down Blocks Split Block Variations Edco MGB Ground Rail — Designed to fit standard 66M1-50 Punch Down Blocks. Allows Edco’s H-Series, COHP, PB Series and other similar Surge Suppressors to access ground when snapped onto the 66M1-50 Punch Down Block. The Standard 66MI-50 block is capable of accommodating up to 25 Edco surge suppressors. US PATENT NO.
Data/Signal Line Protection Edco PC642 Series Zone/Loop/Data The Edco PC642 Series surge suppressor is a two-pair (four-wire) module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed.
Data/Signal Line Protection Edco PC642PTU Pass Thru Unit The Edco PC642PTU is an invaluable tool for troubleshooting Edco card-edgestyle protectors (PC642, PC2TEL, PHC, SLCP Series). Simply unplug the existing Edco card-edge-style protector and plug the Edco PC642PTU (Pass Thru Unit) into the Edco PCB1B base of the circuit to be tested. The Edco PC642PTU will provide continuity to your circuit, thus eliminating the need for a two-man crew or to rewire your circuit for troubleshooting purposes.
Data/Signal Line Protection Edco LCDP Series Data Circuit Protection The Edco LCDP Series is designed to conveniently protect 8 wire, low voltage data circuits and employs two RJ-45 jacks for easy installation. The Edco LCDP utilizes silicon avalanche (solid-state) suppression technology, and exhibits very low capacitance to accommodate high data rates. This unit supports high-speed data rates of over 100 Mbps.
Data/Signal Line Protection Edco TCS-T1 Series T1 Line Protection Against Damaging Transients Protection of your vital T1 lines should be part of the overall power protection plan for your facility. The Edco TCS-T1 Series provides you state-of-the-art protection in a small package. T1 lines need protection from direct and indirect lightning, as well as power disturbances from nearby AC lines.
Data/Signal Line Protection Edco TCS-Multi T1 Series T1/E1 Line Protection The Edco TCS-Multi T1 Series provides you state-of-the-art surge protection in a scalable backplane connected solution. The Edco TCS-Multi T1 Series features two models with different clamping voltages, the Edco TCS-T1S-MX and the Edco TCS-T1DS-MX support in-line connections via 4 pin headers, standard RJ-45 ports or both.
Data/Signal Line Protection Edco DCB Series DC Power Protection for Critical Equipment DC powered equipment is susceptible to transient events that may pass from the AC, Telco, or Coax services to the equipment directly or through other equipment. Harmful transients found in all power services can cause costly damage and downtime of vital DC powered equipment. In response to this problem, the Edco DCB Series for state-of-the-art surge protection was created to fit various application needs.
Data/Signal Line Protection Edco CCTV-1 Closed Circuit TV Protection The Edco CCTV-1 application is specifically designed for lightning protection on closed circuit TV systems. The protector is easily installed with standard type BNC coax connectors. The Edco CCTV-1 offers low loss even at frequencies approaching 500 Mhz. This is important for error-free data communication applications.
Data/Signal Line Protection Edco CATV-DF High Frequency Coax Protector — F-Type The Edco CATV–DF surge protectors are designed to protect sensitive electronic equipment from damage due to excessive voltage or currents generated by lightning or static build-up. Applications include direct broadcast satellite systems, HDTV, and cable modems. The Edco CATV-DF offers low signal loss at frequencies up to 2 gigahertz. Incorporates GDT (Gas Discharge Tube) technology.
Data/Signal Line Protection Edco NET Series SIECOR Network Interface Device The Edco NET Series is a SIECOR Network Interface Line Module with built-in secondary surge protection. In addition to silicon breakover clamping technology (over-voltage), the Edco NET Series incorporates state-of-the-art resettable over-current protection devices — PTCs.
Data/Signal Line Protection Edco FAS-TEL and FAS-31XT RJ11/RJ31X Telephone Protection The Edco FAS-TEL and Edco FAS-31XT are single pair telephone or data line protectors that implement advanced two-stage hybrid design. These units address over-voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology which consists of solid state resettable fuses. The Edco FAS-31XT replaces the RJ31X jack with a protected version.
E
