Brochures and Data Sheets

General Technical Specifications
Features
■ Fast response time
■ 40,000 Amps per phase capacity
■ Failsafe and fused
■ Operational status indicators
■ UL 1449 Third Edition, Type 2 listed
■ 5 year warranty
Edco EMC-240B
120/240 VAC Low Exposure AC Panel Protection
The Edco EMC-240B surge suppressor is designed to protect AC distribution
panel circuits or 120V power supplies feeding sensitive electronic equipment.
Electrically, the unit incorporates MOV and thermal fusing technology. The Edco
EMC 240B is designed to be installed in parallel on standard single phase
120VAC (L,N,G) circuits.
Edco
™
FAS-120AC
120 VAC Medium Exposure AC Panel Protection
The Edco FAS-120AC surge suppressor is designed to protect AC panel
circuits or 120V power supplies feeding sensitive electronic equipment.
Electrically the unit incorporates MOV and thermal fusing technology. This device is
designed to be installed in parallel on standard single phase 120VAC (L,N,G) circuits.
Installation can be close-nipple up to a distribution panel/circuit or hardwired
in parallel up to power supply input terminal screws. Be sure to dress leads as
short as possible.
Operating Voltage 120 VAC
VPR L-N:700V, L-G:700V, N-G:700V
UL Location Type 2
I-Nominal 3 kA
Operating Current NA, Parallel
Total Peak Surge Current 15.5 kA (8 x 20 µs)
Operating Frequency 47-63 Hz
EMI Attenuation (100 kHz to 100 MHz) > 25 dB
SPD Technology Metal Oxide Varistors (MOVs)
Modes of Protection Line-to-Neutral,
Line-to-Ground, Neutral-to-Ground
Status Indication Power On & MOV Functional
Connection Type Wire Leads
Operating Temperature -40°C to +85°C
Dimensions (Inches) 2.5H x 1.5W x 3.0L
Weight 4.2 oz
Certifications ANSI/UL 1449 Third Edition
Features
■ LED indicator
■ Fast response time
■ Thermal fuse
■ L-G, L-N, & N-G protection
■ Compact size
■ Liquid tight conduit fitting
■ 5 year warranty
General Technical Specifications
TVSS/Surge Protective Devices (SPDs)
4
Operating Voltage 120/240 VAC
VPR L-N:600V, L-L:1,200V
Fault Current Rating 42 kAIC
UL Location Type 2
I-Nominal (kA) 3kA
Operating Current NA, Parallel
Total Peak Surge Current 80 kA (8 x 20 µs)
Operating Frequency 47-63 Hz
EMI Attenuation (100 kHz to 100 MHz) > 40 dB
SPD Technology Metal Oxide Varistors (MOVs)
Modes of Protection Line-to-Line,
Line-to-Neutral
Status Indication Power On & MOVs functional
Connection Type Wire Leads
Operating Temperature -40°C to +85°C
Dimensions (Inches) 4.6H x 2.2W x 2.8L
Weight 13.5 oz
Certifications ANSI/UL 1449 Third Edition
Type 2, CUL
Data/Signal Line Protection
21
Edco
™
CAT6-5POE Series
CAT6/CAT5 Power Over Ethernet
The Edco
™
CAT6-5POE Series is designed to work on Category 5 Power-Over-
Ethernet transmission lines as well as Category 6 applications. Ideal to protect
expensive equipment against surges and transients entering a building on
exposed transmission lines.
Features
■ Exceeds CAT5 & 6 transmission values
■ CAT5 POE compatible
■ CAT6 compatible
■ Applications up to 60 VDC @ 300 mA
■ 1 year warranty
Operating Voltage 60 VDC
Clamping Voltage 65 VDC
Operating Current 300 mA
Peak Surge Current 60A (10 x 1000 µs)
Frequency Range 0 to 250 MHz
Insertion Loss < 0.1 dB at 20 MHz
SPD Technology Silicon Avalanche Diode (SAD)
Connection Type RJ-45 Jacks
Operating Temperature -40°C to +85°C
Dimensions (Inches) 0.8H x 1.0W x 2.3L
Weight 1 oz
RJ-45 (Female-Female) CAT6-5POE-FF
General Technical Specifications
Ordering Information