PANELBOARD PROTECTION ON A GLOBAL SCALE
INTRODUCTION WHY APPLETON PANELBOARDS? No matter what environment, location or power requirement, Appleton panelboards have you and your facility covered. From a petrochemical plant in Saudi Arabia to a grain processing facility in America’s heartland, Appleton’s panelboards are there, providing protection and control of electrical apparatus and circuits in hazardous, damp, wet or corrosive environments according to NEC, CEC, IEC and ATEX standards.
PANELBOARD SELECTION GUIDE PANELBOARD RATING EWP APPF ALPF Class I, Division 1 * * * Class I, Division 2 * * * Class II, Division 1 and 2 * ALPN APPN AGPN ALPN APPN AGPN Class III Class I, Zone 1 Zone 1 Zone 2 Zone 21 and 22 FEATURES EWP APPF 3, 3R, 4, 4X, 5, 7BCD, 9EFG, 12 4, 4X, 7BCD, 9EFG 4, 4X, 7BCD, 9EFG 4, 4X, 7BCD, 9EFG 4, 4X, 7BCD, 9EFG 4, 4X, 7BCD, 9EFG Factory Sealed Non-Factory Sealed UL Certification CSA Certification CSAUS Certification IEC Certification ATEX Certificat
PANELBOARD SELECTION GUIDE PANELBOARD RATING D2P XP POWERPLEX DPE DPD D2P XP POWERPLEX DPE DPD 3, 3R, 4, 4X, 5, 7BCD, 9EFG, 12 3, 3R, 4, 4X, 5, 7BCD, 9EFG, 12 4X IP66 IP66 IP66, IK10 IP66, IK10 Class I, Division 1 Class I, Division 2 * Class II, Division 1 and 2 * Class III Class I, Zone 1 Zone 1 Zone 2 Zone 21 and 22 FEATURES Factory Sealed Non-Factory Sealed UL Certification CSA Certification CSAUS Certification IEC Certification ATEX Certification NEMA Type Ingress Protection/Impact Res
4 APPLETON PANELBOARDS
CLASS I, DIVISION 1 & 2 APPN SERIES NON-FACTORY SEALED POWER PANELBOARD – UP TO 600 VOLT These panelboards address a variety of power distribution and lighting needs, and are available in both low-amp and high-amp versions. They offer explosionproof, dust-ignitionproof and watertight protection to meet both NEC and CEC Class I, Division 1 standards. They’re ready to be wired and are commonly used to furnish protection and control of electrical equipment in hazardous locations.
CLASS I, DIVISION 1 & 2 EWP SERIES FACTORY SEALED PANELBOARD The compact EWP Series – designed for use in Class I and Class II, Division 1 manufacturing and processing environments – offers superior protection against explosion where ignitable vapors, gases or combustible dusts are present. EWP is factory sealed. No external branch sealing fittings are needed (except for Division 1 Groups B and C).
CLASS I, DIVISION 1 & 2 APPF SERIES FACTORY SEALED POWER PANELBOARD No matter what the hazard, from the smallest dust particles to combustible gas and vapors in wet and corrosive conditions, APPF Panelboards furnish unwavering protection. These units come factory sealed for an extra measure of safety and convenience. Use them to provide a centrally controlled switching system for large quantities of branch circuits for lighting, heating, small motors and other electrical equipment.
CLASS I, ZONE 1 CLASS I, DIVISION 2, GROUP B, C, & D POWERPLEX 316L STAINLESS STEEL PANELBOARD Appleton’s PowerPlex™ Panelboard delivers component-level protection that increases hazardous location safety and flexibility while greatly reducing and simplifying maintenance. It transfers the flamepath from the panelboard enclosure to individual circuit breaker housings. Its modular design offers the convenience of fieldreplaceable breakers.
CLASS I, ZONE 1 XP SERIES HYBRID FACTORY SEALED PANELBOARD – WITH STAINLESS STEEL TERMINAL ENCLOSURE Tried, true and trusted in northern environments, these XP Panelboards feature a factory sealed breaker compartment with a separate stainless steel terminal enclosure. They are designed for Class I, Division 2 areas where flammable gases or vapors may be present and offer protection and control of electrical apparatus and circuits in hazardous, wet and corrosive environments.
CLASS I, DIVISION 2 D2P SERIES FACTORY SEALED PANELBOARD The D2P Series is designed for use in Class I, Division 2 areas where ignitable vapors or gases may be present, or in Class II, Division 1 areas where combustible dusts are present. The panelboard features a compact design and comes factory sealed without the need for external branch seal fittings. The D2P Series is most commonly used for lighting, heat tracing and protection of other electrical equipment.
ATEX ZONE 1 & 2, ZONE 21 & 22, Exde DPE SERIES ATEX APPROVED INCREASED SAFETY PANELBOARD These compact units provide a centrally controlled switching system for large quantities of branch circuits for lighting in hazardous areas where ignitable vapors, gases or highly combustible dusts are present. DPE Series Panelboards utilize a modular design with non-sealed breakers. DPE Panelboards feature non-sealed breakers in a lightweight polyester or 316L stainless steel enclosure.
ATEX ZONE 1 & 2, ZONE 21 & 22, Exd DPD SERIES FLAMEPROOF PANELBOARD These compact units provide a centrally controlled switching system for large quantities of branch circuits for lighting in hazardous areas where ignitable vapors, gases or highly combustible dusts are present. DPD Series Panelboards utilize a modular design and are flameproof DPD Panelboards feature non-sealed breakers in a gray marine grade aluminum alloy enclosure.
Appleton is our premium line of industrial location products under the EGS Electrical Group family of brands. EGS Electrical Group is a worldwide manufacturer of electrical products for virtually every type of environment. For over 150 years, our brands have been providing a rich tradition of long-term, practical, high quality solutions.
