www.emersonphones.com Manufactured by Southern Telecom Inc. Brooklyn NY. 11232 © 2009 Southern Telecom Inc. All rights reserved. Emerson and the G-Clef logo are registered trademarks of Emerson Radio Corp. Parsippany, New Jersey USA.
Equipment approval information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA. 1 On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not Should you have any questions or problems concerning this product, please contact our customer service department at: 1-877-768-8483 (Toll Free) Monday - Thursday: 9AM - 5PM (EST) Friday: 9AM - 3PM (EST) or via e-mail at cs@southerntelecom.
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 90 Days Limited Warranty In the unlikely event that this product is defective, or does not perform properly, you may within ninety (90) days from your original date of purchase return it to the authorized service center for repair or exchange.
● Answering system memory may be full. Erase some messages. ● You may have accidently pressed the play/stop button during playback and stopped the message. Won’t respond to remote commands ● You must use a tone-dial phone. This phone does not support pulse (rotary) dialing. ● Make sure to enter the correct security code. ● Did unit hang up? If you take no action for a period of time, it automatically hangs up. Poor wireless reception (possible causes for poor reception) ● Aluminum siding.
Unit beeps ● Clean the charging contacts on the cordless handset and base charge cradle with a soft cloth or an eraser. ● Replace the battery. Location of controls Handset layout 1. Display 2. Talk / End 8 Memory dialing doesn’t work ● Did you program the memory location keys correctly? 3. Scroll left / Flash 4. Phone Book ● Did you follow proper dialing sequence? 5. Menu / OK 1 6. Handset ringer ON/OFF Unit locks up and no communication between the base and cordless handset 2 3 4 5 7.
Storing telephone numbers Base layout When the desired telephone number is displayed, press the TO PB if necessary and press the MENU OK MENU OK button. Select SAVE button. Enter the name and press the button. Edit the telephone number if necessary. Press the MUTE 1 MENU OK button for deleting the 2 last character or press and HOLD for deleting the whole number. You can enter a dialing pause (approximately 3 seconds) by pressing the PAUSE button.
Installing the phone Basic operation Answering a call Installing the Handset Battery Press the Inserting the batteries Open the battery compartment cover, install the battery and replace the battery cover. Enter the phone number, using telephone key pad. Delete wrong characters by pressing the MUTE button. Press and HOLD the MUTE button to delete entire entry. Press the Charging the batteries Install the battery pack TALK button , and the phone number is being dialed.
Area code Press the MENU OK / button. Select HANDSET using Select AREA CODE using / and press the key pad and confirm with the MENU OK button. and press the button. MENU OK 5. Allow the phone to charge for 16 hours prior to first use. If you don't properly charge the phone, battery performance is compromised button. Enter the area code using MENU OK CAUTION: To reduce the risk of personal injury, fire, or damage use only the EM6113 power adaptor listed in the user’s guide.
Playback messages / deleting messages Flash time Press You can set the flash time to 100 ms (usually for special services of your telephone provider/delivery state) or 600 ms (e.g. for a telephone exchange). In case of questions please contact your telephone provider or the system administrator of your PBX. Press the MENU button. Select BASE using button. / and press the MENU OK OK button. The messages will be played one after the other. If there are new messages, only these will be played.
Handset name In the idle state the handset name and the internal telephone number is shown in the display. Press the MENU button. Select HANDSET using button. / and press the MENU OK OK Using / using MUTE select HANDSET NAME and press the MENU OK button. Delete the old name . Enter the new name using the digit keys and press the MENU OK button. Key tone The key tone is an acoustical confirmation for a pressed button. Press the MENU button.
NOTE: Depending on (a) how the incoming caller’s phone number is formatted when it is received, and (b) whether or not you previously pre-programmed your local area code into the set up menu, you may need to adjust the format of the incoming caller’s stored phone number, before making the call, press the or button to adjust the number, and try again.
