Data Sheet

Bulletin 71.1:CS800
2
Specications
The Specications section lists the specications for the CS800 Series Regulators. The following information is
stamped on the nameplate of CS800 Series: Type Number, Maximum Outlet Pressure and Spring Range.
Available Congurations
See Table 1
Body Sizes, Material, End Connection and
Pressure Rating
(1)
See Table 2
Maximum Inlet Pressures
(1)
Emergency: 175 psig / 12.1 bar
Operating: See Table 3
Maximum Outlet Pressure
(1)
Emergency (Casing): 15 psig / 1.0 bar
To avoid internal parts damage: 3 psig / 0.21 bar
differential above outlet pressure setting
Outlet Pressure Ranges
(1)
Regulator: 3.5 in. w.c. to 10 psig /
9 mbar to 0.69 bar
See Table 4
Internal Relief Performance
Approximate Internal Relief Start-to-Discharge
Point: See Table 5
Relief Performance:
For Standard Internal Relief: See Figures 9, 11,
13, 15, 17 and 19
For High Capacity Internal Relief: See Figures 10,
12, 14, 16, 18 and 20
Token Relief Performance
Approximate Token Relief Start-to-Discharge:
See Table 5
Maximum Token Relief Discharge Capacities:
See Figure 8
Flow Capacities
With Standard Construction:
See Tables 14 through 16 and 18 through 51
With True-Monitor™ or Slam Shut:
See Tables 14 through 51
With Secondary Seat™ Construction:
See Tables 52 through 66
With Low Inlet Option
(3)
:
See Tables 17 and 53
Orice Sizes, Flow Coefcients and
IEC Sizing Coefcients
See Table 3
Temperature Capabilities
(1)(2)
-20 to 150°F / -29 to 66°C
Spring Case Vent Connection
Internal Relief: 1 NPT
High Capacity Relief: 2-1/2 NPT
External Registration Connection
3/4 NPT
Spring Case Vent and Body Orientation
See Figure 21
Secondary Seat Approximate Lockup Values and
Associated Internal Relief Start-to-Discharge:
See Table 6
TM600 Series True-Monitor Performance
(1)
Inlet Pressure Ratings
Maximum Operating: Up to 125 psig / 8.6 bar
Maximum Emergency: 175 psig / 12.1 bar
Outlet Pressure Range:
12 in. w.c. to 7.5 psig / 30 mbar to 0.52 bar
Type VSX8 Slam-Shut Device
(1)
Maximum Inlet Pressure: 175 psig / 12.1 bar
Maximum Operating Inlet Pressure:
175 psig / 12.1 bar
Construction Materials
CS800 Series Main Valve and Actuator
Body: Gray Cast Iron, Ductile Iron or Steel
Body O-ring: Nitrile (NBR)
Closing Cap: Aluminum
Adjusting Screw: Aluminum, Brass or Zinc-plated steel
Upper and Lower Case: Aluminum
Valve Stem: Aluminum or Zinc-plated steel
Diaphragm Head: Zinc-plated steel
Orice:
Standard: Aluminum
Secondary Seat: Brass
Pusher Post or Internal Relief Valve Seat:
Aluminum or Zinc-plated steel
Diaphragm and Disk: Nitrile (NBR)
Control Spring: Stainless steel or Steel
Relief Valve Spring: Stainless steel
Relief Valve Spring Retainer: Aluminum or
Zinc-plated steel
Vent Screen: Stainless steel
Retaining Ring: Stainless steel or
Zinc-plated steel
Lever Pin: Stainless steel or hardened steel
Spring Seat: Aluminum
Lever: Steel
1. The pressure/temperature limits in this Bulletin or any applicable standard or code limitation should not be exceeded.
2. Product has passed Emerson Process Management Regulator Technologies, Inc. testing for lockup, relief start-to-discharge and reseal down to -40 degrees.
3. Applies to Capacities with Low Inlet Option, which offers Enhanced Flow Performance at Low Inlet pressures for the 2 in. / DN 50 body with 5.5 to 8.5 in. w.c. / 13 to 21 mbar spring range.
- continued -