Instruction manual
ControlWave Gas Flow Computer (GFC Plus) Instruction Manual (CI-ControlWave GFC Plus)
Issue: Feb-2013 Index IND-3
Pulse Counter/Discrete Inputs .......................... 3-10
R
RAM Battery
Disconnecting ............................................... 5-10
Recovery mode switches .................................. 2-15
Repair in field ...................................................... 5-6
Resistance Temperature Device (RTD) ........... 3-12
RS-232 Ports .................................................... 2-26
Cables .......................................................... 2-27
RS-485 Ports .................................................... 2-31
Cables .......................................................... 2-31
configuration switch ...................................... 2-16
Run switching ................................................... 1-13
Running diagnostic software............................. 5-14
S
Sampler ............................................................. 1-13
Site Considerations ............................................. 2-1
Soft Switches
lock/unlock switch ......................................... 2-15
use/ignore switch .......................................... 2-15
Software Tools .................................................... 1-7
Specifications
for temperature, humidity, vibration ................ 2-3
SRAM memory
amount ............................................................ 1-5
control switch ................................................ 2-16
Status codes ..................................................... 5-12
Switches
CPU .............................................................. 2-15
Process I/O board .......................................... 3-2
System Firmware Downloader............................ 5-2
T
Tables
1-1. CPU/System Controller board Variations 1-4
1-2.Process I/O Configurations ...................... 1-6
2-1. CPU System Controller Bd Switch SW1 2-15
2-2. CPU/System Controller Bd Switch SW2 2-15
2-3. RS-485 Configuration Switch (SW3) ..... 2-16
2-4. Power Requirements ............................. 2-19
2-5. Solar Panel Tilt Angle ............................ 2-21
2-6. RS-232 Connectors on CPU ................. 2-27
2-7. RS-232 Port Connector Pin Assignment2-28
2-8. RS-232 Port Alt Connector Pin Assignt 2-28
2-9. RS-485 Connector on CPU ................... 2-31
2-10. RS-485 Port Connector Pin Assignt .... 2-31
2-11. RS-485 Network Connections ............. 2-32
2-12. Ethernet 10/100Base-T CPU Module Pin
Assignments ............................................... 2-33
3-1. Process I/O Configurations ..................... 3-1
3-2. Process I/O Module Switch SW1 ............ 3-2
3-3. Non-Isolated DI General Characteristics . 3-6
3-4. Non-Isolated DO General Characteristics3-7
3-5. Non-Isolated AI General Characteristics . 3-8
3-6. Non-Isolated AO General Characteristics 3-9
3-7. Non-Isolated Pulse Counter/Discrete Inputs
General Characteristics .............................. 3-10
3-8. Non-Isolated High Speed Counter/Discrete
Inputs General Characteristics ................... 3-11
3-9. RTD Connections to CPU/System Controller
Board Connector TB6 ................................. 3-12
4-1. Default Comm Port Settings (by PCB) .... 4-2
5-1. LEDs on CPU System Controller Bd ..... 5-12
5-2. LCD Display Status Codes .................... 5-12
A-1. Module/Board Customer Wiring Connectors
...................................................................... A-2
TB1 Connector .................................................. 2-20
TB2 Connector .................................................. 2-21
Temperature
specifications .................................................. 2-3
Tools ................................................................... 5-1
Transmitters
connecting .................................................... 3-14
Troubleshooting .................................................. 5-1
common communication configuration problems
....................................................................
5-11
general .......................................................... 5-11
U
Updump ............................................................ 5-18
switch ............................................................ 2-16
Upgrading firmware ............................................. 5-2
V
Vibration
specifications .................................................. 2-3
Volume calculations
supported ........................................................ 1-9
Volume integration ............................................ 1-11
W
W3 Backup battery jumper ............................... 2-17
Watchdog
enable switch ................................................ 2-15
WINDIAG .......................................................... 5-14
Wiring
I/O ............................................................ 3-1, 3-4