BP7335 Palazzo 1/9/07 9:05 AM Page 1 READ AND SAVE THESE INSTRUCTIONS PALAZZO™ 54” Ceiling Fan Owner's Manual Model No. CF943AGW00 CF943BZH00 Net Weight: Part No. F40BP73350000 37.9 Lbs. Form No. BP7335 ETL Model No.
BP7335 Palazzo 1/9/07 9:05 AM Page 2 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally.
BP7335 Palazzo 1/9/07 9:05 AM Page 3 This Manual is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly Installed Wire Length Up to 50 ft. 50-100 ft. One Phillips head screwdriver One wire stripper One stepladder Two 60-watt candelabra base bulbs (not supplied) ! Materials Wire Size A.W.G. 14 12 WARNING Before assembling your ceiling fan, refer to the section on proper method of wiring your fan (Page 11).
BP7335 Palazzo 1/9/07 9:05 AM Page 4 A. FAN MOTOR ASSEMBLY B. COUPLING COVER D. FAN BLADES C. CEILING COVER E. BLADE FLANGES F. LIGHT FITTER ASSEMBLY G. HANGER BRACKET H. HANGER BALL/ 6" DOWNROD ASSEMBLY I. GLASS SHADE J. FAN/LIGHT WALL CONTROL K. LOOSE PARTS BAG HI LIGHT MED LOW FAN OFF EMERSON® OFF NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. ON PROTECTIVE PLASTIC BAG 2.
BP7335 Palazzo 1/9/07 9:05 AM Page 5 Electrical Requirements Ceiling Fan Procedures IMPORTANT: Your ceiling fan will not function properly, and may be damaged, if used with any wall dimmer switch or control other than the Emerson Electric Fan/Light Wall Control supplied with the fan, or an optional Emerson Electric SW110 Remote Control.
BP7335 Palazzo 1/9/07 9:05 AM Page 6 Installation of Wall Control 5. Connect the other black wire of wall control to the “load” (black) wire in wall box. Securely connect wires with wire connector supplied. 6. Screw wall control into wall box and install decorator style faceplate (included). Leave wall control in “OFF” mode until fan installation is completed. 7. Refer to page 7 to complete the ceiling fan installation.
BP7335 Palazzo 1/9/07 9:05 AM Page 7 4. Install a wall control in the wall box containing the “hot” wire first. Connect one black wire of the wall control to the “hot” wire. Securely connect wires with wire connectors supplied. 5. Connect the other black wire of the wall control to both remaining traveler wire(s) in the wall box and secure with wire connector supplied. NOTE: Retrofit 3-way installations are likely to include two traveler wires between the two wall boxes.
BP7335 Palazzo 1/9/07 FAN BLADE 9:05 AM Page 8 4. Securely connect the black wire connector of the light fitter assembly to the black motor wire connector. Securely connect the white wire of the light fitter assembly to the white motor wire (Figure 9).
BP7335 Palazzo 1/9/07 9:05 AM Page 9 7. Carefully turn the fan motor assembly upside down in preparation for hanger ball/downrod installation. Place the partially assembled fan into the top half of the styrofoam as shown in Figure 11. Do not rest fan weight on the light fitter sockets. 11. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 13). (Pin and clip are supplied in loose parts bag.
BP7335 Palazzo 1/9/07 9:05 AM Page 10 15. Slide the ceiling cover over the downrod until it rests on the coupling cover (Figure 15). Be sure the cover is oriented correctly, with the large opening at the top. 17. You have now completed the initial assembly of your new ceiling fan. You can now proceed with hanging and wiring your fan. DOWNROD CEILING COVER How to Hang Your Ceiling Fan COUPLING COVER ! WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 17).
BP7335 Palazzo ! 1/9/07 9:05 AM Page 11 How to Wire Your Ceiling Fan WARNING Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.
BP7335 Palazzo 1/9/07 9:05 AM Page 12 f. Cap the receiver yellow wire using a wire connector (supplied). g. Connect the green ground wires from the hanger bracket and the hanger ball to the supply ground wire (bare or green). WARNING ! Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.
BP7335 Palazzo 1/9/07 9:05 AM Page 13 How to Install Your Light Kit OUTLET BOX HANGER BRACKET CAUTION: To avoid risks of burns or other injury, assure power is off before attempting to install or replace the candelabra base bulbs. RECEIVER 1-1/4" THREADED STUDS (2) 1. Install two 60W (maximum) candelabra base bulbs (not supplied) in the sockets of the light fitter assembly (Figure 24). 2. Unscrew the decorative finial nut and threaded washer from the light fitter assembly threaded stud (Figure 24).
BP7335 Palazzo 1/9/07 9:05 AM Page 14 Operating Your Ceiling Fan 5. To turn the light on and off, press and release the LIGHT button. The light will turn on at the light level previously set (see step 4). IMPORTANT Fan installation must be completed, including the installation of the fan blades, before testing of the remote control. Your Fan/Light Wall Control (Figure 26) has full control of your fan and light. However, airflow direction is controlled by a slide switch on the switch housing. 1.
BP7335 Palazzo 1/9/07 9:05 AM Page 15 INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BP7335 Palazzo 1/9/07 9:05 AM Page 16 Maintenance Accessories IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan 1. Downrod Extension Kits (see store or catalog). Periodic cleaning of your new ceiling fan is the only maintenance that is needed. 2. Ceiling Fan Controls (see store or catalog). 3. Blades (see store or catalog). When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish.
BP7335 Palazzo 1/9/07 9:05 AM Page 17 WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX ! OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE 1. Fan will not start. PROBABLE CAUSE 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan. 3. Fan/Light Wall Control is OFF. 4. Code switches in remote control receiver and Fan/Light Wall Control are not set in the same position. 2. Fan sounds noisy. 1. Blades not attached to fan. 2.
BP7335 Palazzo 1/9/07 9:05 AM Page 18 Repair Parts 1 2 9 3 24 14 6 10 11 15 23 HI LIGHT MED LOW REV FAN OFF OFF ON 20 8 7 16 4 5 21 18 19 17 22 12 13 Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • NAME OF ITEM • PART DESCRIPTION • MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing.
BP7335 Palazzo 1/9/07 9:05 AM Page 19 Repair Parts Listing Part Numbers Key No. Description Model No. CF943AGW00 Model No.
BP7335 Palazzo 1/9/07 9:05 AM Page 20 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for a lifetime of your ceiling fan.
