Instruction Manual

67C Series
2
Specications
TheSpecicationssectiongivessomegeneralspecicationsforthe67CSeriesregulator.Alabelonthespring
case gives the control spring range for a given regulator as it comes from the factory.
Body Size, Inlet and Outlet Connection Style
1/4 NPT
Maximum Inlet Pressure (Body Rating)
(1)
All except Types 67CS and 67CSR:
250 psig / 17.2 bar
Types 67CS and 67CSR: 400 psig / 27.6 bar
Outlet Pressure Ranges
See Table 1
Maximum Emergency Outlet Pressure
(1)
50 psi / 3.4 bar over outlet pressure setting
Wide-Open Flow Coefcients
Main Valve: C
g
: 11.7; C
v
: 0.36; C
1
: 32.2
I nternal Relief Valve: C
g
: 1.45; C
v
: 0.045; C
1
: 32.8
IEC Sizing Coefcients
Main Valve: X
T
: 0.66; F
L
: 0.89; F
D
: 0.50
Accuracy
Inlet Sensitivity for Nitrile (NBR) and
Silicone (VMQ) Elastomers: Less than 0.2 psig /
14 mbar change in outlet pressure for every
25 psig / 1.7 bar change in inlet pressure
Inlet Sensitivity for Fluorocarbon (FKM)
Elastomers: Less than 0.4 psig / 28 mbar change
in outlet pressure for every 25 psig / 1.7 bar
change in inlet pressure
Repeatability for Nitrile (NBR) and Silicone (VMQ)
Elastomers: 0.1 psig / 7 mbar
(2)
Repeatability for Fluorocarbon (FKM)
Elastomers: 0.3 psig / 21 mbar
(2)
Air Consumption: Testing repeatedly shows
no discernible leakage
Types 67CR, 67CSR, 67CFR and 67CFSR
Internal Relief Performance
Low capacity for minor seat leakage only; other
overpressure protection must be provided if inlet
pressure can exceed the maximum pressure rating
of downstream equipment or exceeds maximum
outlet pressure rating of the regulator.
Approximate Weights
Types 67C, 67CR, 67CF and 67CFR:
1 pound / 0.5 kg
Types 67CS and 67CSR:
2.5 pounds / 1.1 kg
Types 67CFS and 67CFSR:
4 pounds / 1.8 kg
Temperature Capabilities
(1)
With Nitrile (NBR)
Standard Bolting: -20 to 180°F / -29 to 82°C
Stainless Steel Bolting: -40 to 180°F / -40 to 82°C
With Fluorocarbon (FKM):
Polyethylene Filter
(5)
(Standard):
0 to 180°F / -18 to 82°C
Polyvinylidene (PVDF), Stainless steel or
Glass Filter (Optional):
0 to 300°F / -18 to 149°C
With Silicone (VMQ)
(3)
Diaphragm and Low
Temperature bolting: -60 to 180°F / -51 to 82°C
With Gauges: -40 to 180°F / -40 to 82°C
Smart Bleed™ Check Valve Setpoint
6 psi / 0.41 bar differential
Types 67CF, 67CFR, 67CFS and 67CFSR
Filter Capabilities
Free Area: 12 times pipe area
Micron Rating:
Polyethylene Filter
(5)
(Standard): 5 microns
Glass Fiber Filter (Optional): 5 microns
PVDF or Stainless Steel Filter (Optional): 40 microns
Drain Valve and Spring Case Vent Location
Alignedwithinletstandard,otherpositionsoptional
Pressure Registration
Internal
Options
All Types
• Handwheeladjustingscrew
• Inletscreen
• NACEMR0175orNACEMR0103construction
(4)
• Panelmount(includesspringcasewith1/4NPT
vent, handwheel and panel mounting nut)
• Closingcap(availableonspringcasewith
1/4 NPT vent)
• Fluorocarbon(FKM)elastomersforhigh
temperatures and/or corrosive chemicals
• Silicone(VMQ)elastomersforcoldtemperatures
• FixedBleedRestriction
• Triplescaleoutletpressuregauge(Brassor
Stainless steel)
• Stainlesssteelstemonthevalveplug
• Tirevalveorpipepluginsecondoutlet
Types 67CFR and 67CFSR only
• SmartBleedinternalcheckvalve
• Largedripwellwithmanualorautomaticdrain
Types 67CF and 67CFR only
• Stainlesssteeldrainvalve
1.Thepressure/temperaturelimitsinthisInstructionManualandanyapplicablestandardorcodelimitationshouldnotbeexceeded.
2. Repeatability is the measure of the regulator’s ability to return to setpoint consistently when traveling from steady state to transient to steady state.
3.Silicone(VMQ)isnotcompatiblewithhydrocarbongas.
4.ProductcomplieswiththematerialrequirementsofNACEMR0175.Environmentallimitsmayapply.
5. Do not use in high aromatic hydrocarbon service.