Instruction Manual

133 Series
13
* Recommended spare parts.
1. If the 2 inches w.c. to 2 psig / 5 mbar to 0.14 bar springs listed under Type 133L are used in the Type 133H, the pressure ranges will increase by approximately 1 inch w.c. / 2 mbar due to
the weight of the Type 133H parts (assuming that the actuator is installed above the body).
40A3070
Figure 11. Type 133H Assembly
Key Description Part Number
12 Spring Steel (continued)
Type 133HP (continued)
Steel
6 to 20 psig / 0.41 to 1.4 bar, Silver 10C1238X012
16 to 30 psig / 1.1 to 2.1 bar, Red 10C1240X012
26 to 40 psig / 1.8 to 2.8 bar, Blue 10C1241X012
36 to 50 psig / 2.5 to 3.5 bar, Green 10C1242X012
45 to 60 psig / 3.1 to 4.1 bar, White 10C1243X012
13 Spring Seat, Plated steel
Types 133H, 133L, and 133Z 10A3052X012
Type 133HP 1P787724152
14 Diaphragm Plate, Steel
Type 133H (1 required) 1D555725012
Type 133L (1 required) 1J881725072
Type 133Z (2 required) 1J881725072
Type 133HP (1 required) 22B3514X012
15* Diaphragm, Nitrile (NBR) and Nylon (PA)
Types 133H, 133L, and 133Z 1N150802052
Type 133HP 22B3514X012
Fluorocarbon (FKM)
(for Types 133L and 133H only) 1N150802402
16 Sealing Diaphragm Plate, Zinc-plated steel
Types 133H, 133L, and 133Z 1D475725062
Type 133HP 12B3517X012
17* Sealing Washer, Zinc-plated steel
(2 required for Types 133L, 133H, and 133Z;
1 required for Type 133HP) 1F990428982
18 Stem, Stainless steel
Types 133H and 133L 20A3053X012
Type 133Z 10A3069X012
Type 133HP 37B3942X012
Key Description Part Number
19* O-ring
Nitrile (NBR)
(2 required for Types 133L, 133H,
and 133HP; 1 required for Type 133Z) F1367806562
Fluorocarbon (FKM)
(2 required for Types 133L and 133H only) 1E5914X0062
20 Hex Nut
Types 133H, 133L, and 133Z, Aluminum 1D5297X0012
Type 133HP, Zinc-plated steel 1A413224122
21 Diaphragm Plate, Plated steel 10A3054X012
22* Diaphragm
Nitrile (NBR) and Nylon (PA) 10A3055X012
Fluorocarbon (FKM)
(for Types 133L and 133H only) 10A3055X022
23 Washer, Steel (2 required) 10A3056X012
24* Guide Bushing, Nylon (PA) 10A3057X012
25 Stem Sleeve, 303 Stainless steel 10A3061X012
26 E-ring, Plated steel 1F599428982
27 Roll Pin, 420 Stainless steel 1E954028992
28* Valve Disk Assembly
Aluminum / Neoprene (CR) 10A3058X012
Aluminum / Fluorocarbon (FKM)
(for Types 133L and 133H only) 10A3058X032
29 Registration Disk, Nylon (PA) 10A3060X012
30 Washer, Zinc-plated steel 1H723125072
31 Hex Nut, Zinc-plated steel 1C121928982
32* O-ring
Nitrile (NBR) 1J1079X0012
Fluorocarbon (FKM)
(for Types 133L and 133H only) 1J1079X0022
33 Stud, Alloy steel (4 required) 10A3062X012
9
11
39
22
35
21
6
31
29
28
4
3
13
20
12
10
2
36
25
23
18
16
17
8A
14
40
7
32
15
8J
8E
5A
27
19
26
30
8D
8G
19
8F
5
24
34
33
8H
1
8C
8B
APPLY LUBRICANT (L) OR SEALANT (S)
(1)
1. Lubricant and sealant must be selected such that they meet the temperature requirements.