EOS-6000 Series Optical A/B Switch User Manual – DC Version For more information on this and other products: Contact Sales at EMCORE 626-293-3400, or visit www.emcore.com.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Table of Contents Table of Contents ....................................................................................................................................2 Safety Information....................................................................................................................................3 Power Requirements .............................................................................................................
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Safety Information Power Requirements The system operates from a DC power source that supplies -36 to -60 V DC. Safety Instructions The following safety instructions must be observed whenever the unit is operated, serviced, or repaired. Failure to comply with any of these instructions or with any precaution or warning contained in the user’s manual is in direct violation of the standards of design, manufacture, and intended use of the unit.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Getting Started Before Initializing and Operating the Unit 1. 2. 3. 4. Inspect the optical switch for any signs of damage, and read the User’s Manual thoroughly. Install the optical switch as specified in the Getting Started section. Ensure that the optical switch and any devices or cords connected to it are properly grounded.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Storing and Shipping To maintain optimum operating reliability, do not store the unit in locations where the temperature falls below -25°C or rises above 65°C. Avoid any environmental condition that can result in internal condensation. Ensure that these temperature and humidity requirements can also be met whenever the unit is shipped.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 3. Inspect the appearance of the unit for any shipping damage. 4. In case of damage, document and inform the shipping company and your local representative. 5. Save the shipping boxes and their inserts for any future reshipment for upgrade or repair. NOTE: In the event of a reshipment back to the manufacturer, any additional damage caused by not using the original boxes will be considered the responsibility of the customer.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Optical Switch Outline Drawing (Units in mm) 7 of 14 EMCORE Broadband 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 Copyright 2008.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Operating the Optical Switch WARNING To avoid the risk of injury or death, always observe the following precautions before initializing the optical switch. If using a voltage-reducing autotransformer to power the optical switch, ensure that the common terminal connects to the earthed pole of the power source. Use only the type of power cord supplied with the optical switch.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Operating Environment In order for the optical switch to meet the warranted specifications, the operating environment must meet the following conditions for temperature and humidity. WARNING 1. Do not use the optical switch outdoors. 2. To prevent potential fire or shock hazard, do not expose the optical switch to any source of excessive moisture. Temperature The optical switch can be operated in the temperature range of 0°C to 50°C.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Front Panel View Power Indicator Main Input Status Backup Input Status Output status Manual switch Rear Panel View (DC) Main Line Backup Line Input Input Output RS232 Port for management Com Port Select Switch RJ45 Port for management DC Terminal Block Power Switch 10 of 14 EMCORE Broadband 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 Copyright 2008.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Sample Application The diagram below shows a typical CATV application that allows fully redundant transmitters and fiber paths, with automatic protection to the network via the EOS-6000 switch. Contact your Emcore sales representative for more information on Emcore’s complementary product lines. Functionality Network management The EOS-6000 supports SNMP1.0 protocol for remote network management.
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 a. Above the Pre-alarm power value (dBm), the output indicator is green; b. Above the Switching Threshold but below the Pre-alarm power value (dBm), the output indicator is yellow; c. Below the Switching Threshold, the output indicator is red. 3) If the optic power of either the main line or backup line is higher than the Switching Threshold, the output indicator is green, otherwise red.
EOS 6000 Optical A/B Switch Optical Connector Monitoring Interfaces USER MANUAL | SEPTEMBER 9, 2008 Operating Temperature SC/APC 100 Base-T Ethernet Rear Panel RS-232 interface LED Indicators 0°C to 50°C Storage Temperature Power Consumption -25°C to 65°C 5W Supply Range (VDC) Dimensions Other styles available SNMP V1 Reserved for Factory Use Power, Main, Backup, and Output Indicators Maximum 36 - 60 VDC 430x300x44mm Applicable Standards Compliance EMI/EMC EN55022:2006 conducted emissions, info
EOS 6000 Optical A/B Switch USER MANUAL | SEPTEMBER 9, 2008 Laser Safety Class 1 Device This equipment is inherently classified as a Class I laser product, since the equipment contains no laser or light emitting diode (LED) of a higher class number. WARNING Although unit is classified as a Class 1 device, a hazard can exist due to laser radiation emitting from the output port of the optical switch, and thus eye safety precautions should be adhered to at all times.
