Installation Guide

4
1. Install the sill spacer clip (N) under the latch
side sweep screw and tight against the
bottom of the sweep (G/H). Tighten the
sweep screw to retain the sill spacer clip in
place.
2. Install the latch side spacer clip (M) over the
latch side of the door frame as shown. This
clip should be approximately 6” from the
bottom of the door frame.
PREPARE
STORM
DOOR FOR
INSTALLATION
(Left Hand)
3
a
e
G
For a Right Hand Installation, go to Page 7.
M
N
1. Position the hinge rail along the hinge-side
edge of the door frame so the bottom hole
of the 2nd hinge up from the bottom lines
up with the bottom hole from the screw
removed in step 3a. NOTE: The top of the
hinge rail should extend approximately 3/16”
beyond the top of the door frame.
2. Pre-drill 1” deep pilot holes in door frame at
each hinge and fasten using 1” unpainted
screws from the pink bag in the installation kit.
1. Sweep H only: Slide the sweep n (I) into
the track in the sweep. Crimp both ends of
the track to secure the n. Trim o excess
sweep n material and properly discard.
1. Install the door sweep (G/H) so that it is
centered across the width of the door frame
and pressed tight against the bottom of the
door frame. Doors with vinyl sweeps were
shipped with the sweep on the side of the
door frame.
2. Center punch and then predrill 1/8” pilot holes
at the bottom of the slot for future adjustment,
then attach the sweep using painted 1/2”
screws from the pink bag.
1. Place the latch side edge of door frame on
the ground. TIP: Lay on door carton.
2. Identify the top of the hinge rail (D).
3. Remove the two middle hex head screws
from the hinge side edge of door frame and
properly discard.
BOTTOM
PARTE INFERIOR
BAS
b c
H
I
H
G
H
OR
H
TOP
PARTE SUPERIOR
HAUT
i
i
VIEW
i
i
i
i
i
i
i
i
VIEW
i
i
VIEW
i
i
i
VIEW
BOTTOM
PARTE INFERIOR
BAS
X
X
XX
VIEW
1”
x 8
x 2
or
x 4
1/2”
Painted
PINK BAG / BOLSA ROSA / SAC ROSE
N
D
M
Tools needed:
!
!
1/2” 1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/8”
!
!
1/2” 1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
!
!
1/2” 1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
!
!
1/2” 1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
E
d
Do not drill completely through door. This will create an
unnecessary hole in the door and may cause water and
air inltration.
CAUTION
L
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
G
H
PROFILE
PERFIL
PROFIL