User manual

ManualsBrandsEMBRICK ManualsPLCVIM0-0118-00

Slave Components - P-Modules (Process Control)

Product Catalogue all information for reference only - technical changes reserved - rev. 11p Page 117 of 184

6.5.4 P-6Rel5DiPow-01

6.5.4.1 Brief Description

The module includes 6 digital relay

outputs, 5 n-switching inputs and 1

inductive AC-current senor.

The module has two potential free

change-over relays which can switch

a continouse current of 4A.

Four other relays are able to supply

up to 230V. 2 of these are closing

and the other 2 are switch-over. Each

of the supplying relay can switch up

to 5A. The max. permant sum current

over the supply outputs is 5A.

6.5.4.2 Connection and Indication-/Operation-Elements

2x Relay-Output, NO, supply switching

2x Relay-Output, CO, supply switching

2x Relay-Output, CO, potential free

5x Digital-Inputs, 2-wire, common gnd

1x AC-Current Input,2/20 Ap

Modul ID

5-302

Order No.

CAE_P-6Rel5DiPow-01

Terminals

push-in (≤ 0.5mm²)

Core

M16A

Size

10 eU (110mm x 72mm)

FCP

1-1-1

Variants

4………6

1………3 7…............................16…17...............22…23………..……..32

Status LED

Output LEDs

Relay1

…Relay4

(from left to right)

Output LEDs

Relay5

…Relay6

(from left to right)

Input LEDs

Di1

…Di5

(from left to right)

Output Terminals

Relay 1, 2

(closing contact)

Relay 3, 4, 5, 6

(switchover contact)

T7…22 (from left to right)

Input Terminals

T23...32

(from left to right)

Power Terminals

L, N

(from top to bottom)

Protection Earth Terminals

T1..T6

Summary of content (6 pages)

PAGE 1
Slave Components - P-Modules (Process Control) 6.5.4 P-6Rel5DiPow-01 2x Relay-Output, NO, supply switching 2x Relay-Output, CO, supply switching 2x Relay-Output, CO, potential free 5x Digital-Inputs, 2-wire, common gnd 1x AC-Current Input,2/20 Ap Modul ID 5-302 Order No. CAE_P-6Rel5DiPow-01 Terminals push-in (≤ 0.5mm²) Size Variants 10 eU (110mm x 72mm) Core M16A BBFCP 1-1-1 - 6.5.4.
PAGE 2
Slave Components - P-Modules (Process Control) 6.5.4.3 Terminal Assignment Circuit Example Ident. Ter.
PAGE 3
Slave Components - P-Modules (Process Control) 6.5.4.4 LED Indications Output LED1..6 ............................ status indication of the relays 1…6 Input LED7..11 ............................ status indication of the Inputs Status-LED .................................. module status (see 6.1.1) 6.5.4.5 Application Note In addition to the notes in chapter 4, please regard the following:      Make sure that the GND of the analog signals is connected to the 0V terminal.
PAGE 4
Slave Components - P-Modules (Process Control) 6.5.4.6 Technical Data Note: For further global specifications refer to chapter 4 Input: Number of digital inputs ........... 5 Connection technology ......... 2-wire, common ground Type ....................................... n-switching Threshold low/high ............... approx. 7,7/13,2V Open input voltage ................ approx. 21V @ internal 24V supply from bus Pull down current .................. approx.
PAGE 5
Slave Components - P-Modules (Process Control) 6.5.4.7 Process Data Image: Organisation of the user data communicated via brickBUS: Out-Userdata from Master to Slave In-Userdata to Master from Slave total: 1 Bytes total: 2 Bytes Byte 0 Function Output setting rC Assign... ... + eB_B0, 5, ... ... ... + eB_B0, 0, ... ... + eB_B0, 6, ... Byte 0, 1 Function Analog-Input 1 rC Assign... 2 Digital Input ... + eB_B2, 1, ... ... ... + eB_B2, 5, ... ... + eB_W0, 0, ...
PAGE 6
Slave Components - P-Modules (Process Control) 6.5.4.8 Programming Note Beside the notes in chapter 4, please regard the following these:  A calibration has to be done in the applications software.