Product data

CompactPCI Bus
■ 3U CompactPCI CPU board PICMG
Spec. 2.0 R3.0 compliant
■ 32-bit CompactPCI system slot functionality
with 7 possible external loads
■ PCI-to-PCI bridge
■ Single-slot solution
■ Rear I/O via J2/P2
■ V(I/O): +5V (+3.3V on request)
CPU
■ Intel
®
Celeron
®
M (ULV) or Pentium
®
M
■ 600MHz..1.8GHz
Chipset
■ Intel
®
i855 chip set consisting of:
■■ 82855GME Graphics/Memory Controller
Hub (GMCH)
■■ 82801D I/O Controller Hub (ICH4)
■■ 82802 Firmware Hub (FWH)
Graphics
■ Integrated VGA graphics controller
■■ Connection at front panel (DVI-I connector)
or via rear I/O / transition module
■■ Maximum resolution: 2048 x 1536,
16M colors @ 75Hz refresh rate (analog);
1600 x 1200, 16M colors @ 60Hz
refresh rate (digital)
■■ PanelLink Digital technology
Memory
■ CPU L2 Cache
■■ Celeron
®
M: 512KB
■■ Pentium
®
M: 1MB or 2MB
■ Up to 1 GB DRAM
■■ One 200-pin SO-DIMM socket
for DDR SDRAM modules
■■ PC2100/2700
■■ DDR266/333-SDRAM
Interfaces
■ 10/100/1000Mbits/s Gigabit Ethernet
controller
■■ RJ45 interface at front panel or
via rear I/O transition module
■■ Two display LEDs in RJ45 connector to
signal LAN Link and Activity status
■■ Supports network boot
■ USB 2.0 interfaces
■■ Conforming to Open HCI 1.0a
■■ Two ports via Type A connectors
at front panel
■■ Two ports via rear I/O transition module
■■ Data throughput up to 480Mbits/s
Mass Storage
■ Fast IDE ports (UDMA5)
■■ One IDE port for local CompactFlash
or 1.8" hard disk or connection to mezzanine
expansion board with onboard hard disk
drive or external device (Secondary IDE)
■■ One IDE port via rear I/O transition module
(Primary IDE)
■ CompactFlash interface (Secondary IDE)
■■ Type I and Type II
■■ True IDE
■■ For CFA ATA memory card or Microdrive
Software Support
■ Phoenix BIOS for industrial applications
■ Windows NT, Windows 2000/XP,
Embedded Windows
■ Linux (on request)
■ VxWorks (on request)
■ QNX (on request)
■ RTX (on request)
Product Options
Secondary IDE
■ 1.8" hard disk adapter instead of CompactFlash
Rear I/O on F9
■ Via rear I/O transition module F9R
■ Primary IDE (onboard)
■ Two USB 2.0 ports (back panel)
■ PS/2 keyboard/mouse (back panel)
■ COM1 (onboard, TTL level), for connection
of MEN SA-Adapters
■ Gigabit Ethernet (back panel)
■ VGA analog video (back panel)
I/O on Expansion Board F9E
■ COM1 (front)
■ USB 2.0 (front)
■ AC'97 audio (front)
■ PS/2 keyboard/mouse (front)
■ Secondary IDE usage for
■■ CompactFlash, or 1.8", or 2.5" hard disk
■ Floppy disk
■ Local GPIO
■ Rear I/O
Miscellaneous
■ F9 for usage in 64-bit CompactPCI systems
■ Extension possibility for F9 to 6U height
■ 2
nd
Ethernet port via I/O extension board
■ More different legacy I/O combinations via
special I/O extension board
■ One-piece 3U/8TE front panel for F9 in com-
bination with different I/O extension boards
8
CompactPCI
MEN CompactPCI
■ Pentium
®
M (LV) up to 1.8 GHz
■ Celeron
®
M (ULV) 600 MHz
■ 1-slot 32-bit CompactPCI system master
■ PXI system controller
■ 1 GB DDR RAM (SO-DIMM), CompactFlash
■ Graphics controller / DVI-I (front)
■ Gigabit Ethernet (front)
■ Dual USB 2.0 (front)
■ COM 1, IDE, 2 USB, keyboard/mouse via rear I/O
F9 – 3U CompactPCI/PXI Pentium
®
M SBC