Product data
6
CompactPCI
MEN CompactPCI
CompactPCI Bus
■ 3U CompactPCI CPU board PICMG
Spec. 2.0 R3.0 compliant
■ 32-bit CompactPCI system slot functionality
with 7 possible external loads
■■ The board only functions properly
with a 32-bit backplane and rear I/O,
no 64-bit backplane
■ PCI-to-PCI bridge
■ Double-slot solution (plus 1 mechanical slot
for hard disk)
■ V(I/O): +3.3V or +5V (Universal Board)
■ Also available as busless version (with ext. 5V)
CPU
■ Celeron
®
or Pentium
®
III
■ 400MHz or 650MHz or 933MHz processor
core frequency
■ 256KB or 512KB L2 cache
■ 100MHz or 133MHz system bus frequency
Graphics
■ Integrated VGA graphics controller
■■ VGA connector at front panel
■■ Up to 1600 x 1200 pixels
Memory
■ 512MB SDRAM
■■ One 144-pin SO-DIMM socket for
synchronous DRAM modules
■■ 133/100MHz memory bus frequency
■ CompactFlash interface
■■ Type I, True IDE
■■ DMA is supported
■ Serial EEPROM 4kbit for factory settings
Interfaces
■ Two 10/100Mbits/s Ethernet channels
■■ 82551(ER) controller
■■ Two RJ45 interfaces at front panel
■■ Four onboard LEDs to signal LAN Link
and Activity status
■■ Supports network boot
■ Two USB 1.1 interfaces
■■ UHCI implementation
■■ Via rear I/O (J2)
■■ Data throughput up to 12Mbits/s
■■ Supplies High-Power (500mA)
without external power supply
■ PS/2 keyboard/mouse
■ UART RS232 serial interfaces COM1 / COM2
■■ One 9-pin D-Sub connector at front panel
■■ One via onboard SA-Adapter
■■ Up to 230 kbaud
■■ FPGA-controlled
■ UART serial interface
■■ Via onboard SA-Adapter
■■ FPGA-controlled
Mass Storage
■ Fast IDE ports (UDMA4)
■■ One IDE hard-disk/CD-ROM port
via I/O connector to carrier board
■■ One IDE port for local CompactFlash
Additional I/O through FPGA
■ Available at I/O connector
■ Depending on FPGA composition
■ COM 1 and 2 at the front (see Interfaces)
■ SRAM
■ GPIO
PCI Interface
■ 32-bit PCI interface at PCI-104 connector J1
■ Support of 4 external masters
Miscellaneous
■ Real-time clock, backed up by the carrier board
■ Integrated hardware monitor
Software Support
■ Award BIOS, Windows, Linux, VxWorks,
QNX, RTX
Product Options
SA-Adapters
■ Up to 8 SA-Adapters
■ Mostly implemented in onboard FPGA
■ RS232, RS422/485, binary I/O, AC'97, CAN...
■ Example config.: 2 CAN (SA08), 2 RS485
(SA02), 1 RS232 (SA03), 1 digital I/O (5 O, 5 I,
3 I/O –SA15),1AC'97 w. opt. isolation (SA12)
Rear I/O on F11
■ Via rear I/O transition module F9R
■ Primary IDE (onboard)
■ Two USB 1.1 ports (back panel, alternatively
to F11 front panel)
■ PS/2 keyboard/mouse (back panel,
alternatively to F11 front panel)
■ COM1 (onboard, TTL level), for connection
of MEN SA-Adapters
IDE 2.5" hard disk
AC'97 AC'97 instead of SRAM
Busless Also available with ext. 5V
■ 32-bit cPCI/PXI system slot or stand-alone, 12 HP
■ ULP Pentium
®
III up to 933 MHz
■ ULV Celeron
®
up to 650 MHz
■ Up to 512 MB DRAM, 2MB SRAM, CompactFlash
■ 2 Fast Ethernet, COM 1, 2 USB 1.1 (front)
■ Option: COM 2 (front)
■ VGA/digital video output, keyboard/mouse (front)
■ Up to 1600 x 1200 pixels
■ IDE (on-board)
■ Prepared for 2.5" hard disk on board
■ FPGA – further programmable I/O functions
■ Option: up to 7 SA-Adapters
F11 – 3U CompactPCI/PXI Pentium
®
III SBC