COLORTOUCH CONTROL BOX WITH REMOTE/WIFI CONTROL INSTALLATION AND OPERATION MANUAL USER MANUAL Model: COLOR TOUCH Series EMLI22022102
PAGE CONTENT SYNCHRONIZE COLOR SETTING OF TWO ZONES COLORTOUCH CONTROL BOX P1 TABLE OF CONTENT 2 .... 1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS 2 .... 2. PRODUCT INTRODUCTION 3 .... 3. SPECIFICATION 4 .... 4. INSTALLATION 4.1 WIRING DIAGRAM 5 .... 5. CONTROL BOX PANEL OPERATION 6 .... 6. COLORTOUCH REMOTE HANDSET 6.1 LEARNING PROCESS OF REMOTE 6.2 THE REMOTE HANDSET 6.3 BATTERY REPLACEMENT 8 .... 7. COLOR TOUCH WIFI CONNECTION 8 .... 8. MAINTENANCE AND TROUBLE SHOOTING 9 .... 9.
1. IMPORTANT SAFETY AND INSTALLATION INSTRUCTIONS Please read the manual carefully before commencing installation. This manual contains important information about the correct installation and operation of E- Lumen X lights. 1. This ColorTouch control box must be installed by a licensed or certified electrician or a qualified serviceman in accordance to the requirements of your government standard or local authorities.
* AC main switch Zone 2 Zone 1 3.
CONTROL BOX DISPLAY AND FUNCTION KEYS Reset Button All Button Z2 Button Lean key Display Standby ON/OFF Button Z1 Button Main Power Switch Power Cord Learn key Zone 2 Output Zone 1 Output Remote Handset Color Wheel Mode Display Brightness ALL(Z1+Z2) Z2 Z1 RESET Battery Compartment 4. INSTALLATION 1. Remove the mounting bracket from the control box, position the mounting bracket to the desired fitting place and mark on the wall with the location of the drilled holes. 2.
4.1 WIRING DIAGRAM 1. Unscrew the screws from the bottom and take out the housing carefully. 2. Remove the waterproof connector nut and put the transformer 110-220Vac cable through it. 3. Mount the two wires on the connector as figure. The terminal voltage is 110-220Vac and never mount the light on it directly! When input terminal voltage is 220Vac, must connect to 220Vac transformer , not 110Vac transformer . Color Touch Control Box PCB AC Mains Power cord Zone 1 Power cord Zone 2 Power cord 5.
6. RESET Button - Press the button to reset all the pool lights connected to Z1 & Z1 to cool white color. 6. COLORTOUCH REMOTE HANDSET Each Each control box is associated with a ColorTouch remote handset. It needs to pair the control box and hadset by learning process as below: 6.1 LEARNING PROCESS OF REMOTE Switch off main power button of the box before pressing the learn key of the box.
6.2.1 COLORTOUCH MODE It is the default control mode after learning. 1. The mode display LED under at the center of color wheel will be flashed in red color and ready to touch. 2. The ColorTouch remote choose direct color pick up just by touch the color area. 3. The rainbow color key is a toggle key for multiple modes of auto color change. 4. There are three level of brightness for light brightness adjustment by touch the desired brightness button. 5.
7. COLOR TOUCH WIFI CONNECTION The latest Color Touch control box armed with WIFI access function from your home router. Therefore, you can control the E-lumen X lamp color, brightness, ON/OFF and etc same as remote handset. 1. The Android app can be download from Android marketplace. 2. Install the apps as usual and below icon will be shown on screen when installation finished. 3. Open your cell phone WIFI setting and connect to SSID “ColorTouch” with password 12345678. 4.
9. REPLACEMENT PARTS Description Qty Item No. Part No.
10. TERMS OF THE WARRANTY As original purchaser of this equipment have purchased from Emaux Water Technology Co Ltd, through Authorized International Distributor or Dealer, warrants its products free from defects in materials and workmanship under normal use during warranty period. The warranty period begins on the day of purchase and extends only to the original purchaser. It is not transferable to anyone who subsequently purchases the product from you. It excludes all expendable parts.
EMAUX WATER TECHNOLOGY CO., LTD YOUR PREMIER SUPPLIER www.emauxgroup.
