User's Manual

FCC Compliance information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Caution : Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
IC Radiation Exposure Statement for Canada
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. To maintain
compliance with IC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna
during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
-This device may not cause interference and
-This device must accept any interference, including interference that may cause undesired operation of
the device. To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this
device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its
transmit antenna) that is installed outdoors is subject to licensing.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device complies with Industry Canada licence-exempt RSS standard(s).
CAN ICES-3(B)/NMB-3(B)
The radiated output power of the Wireless Device is below the Industry Canada(IC) radio frequency exposure limits.
This equipment complies with IC RF exposure requirements set forth for an uncontrolled environment.
Déclaration d’Industrie Canada relative à l’exposition aux ondes radio
Cet appareil est conforme aux limites d’exposition aux radiations d’Industrie Canada définies pour un
environnement non-contrôlé. Pour maintenir la conformité avec les exigences d’exposition RF d’IC, veuillez éviter
tout contact direct avec l’antenne pendant l’émission. Les utilisateurs finaux doivent suivre
les instructions de fonctionnement spécifiques pour satisfaire la conformité aux expositions RF.
Son utilisation est sujette aux deux conditions suivantes:
-Cet appareil ne peut pas causer d’interférence, et
-Cet appareil doit accepter toute interférence, y compris les interférences qui pourraient causer un
fonctionnement non souhaité de l’appareil. Pour éviter les interférences radio avec le service sous licence
(c’est à-dire le partage de canal avec les systèmes de téléphonie satellite), cet appareil est destiné
à être utilisé en intérieur et loin des fenêtres pour fournir un blindage maximal.
Tout appareil (ou son antenne d’émission) qui est installé en extérieur est sujet à cette licence.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
CAN ICES-3(B)/NMB-3(B)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d’exposition aux fréquences
radio d’Industry Canada (IC).