Installation manual

Preparation for Installation
1. Basic requirements
1) All the electronic operation should be strict compliance with the local electrical safety regulations, fire prevention regulations
and other related regulations at the installation place.
2) Check whether all the accessories are there according to the packing list, make sure that the place and installation mode are
conform to the demands, if not, please contact the supplier.
3) Please use this product according to the working environment.
2. Check installation space.
Make sure the place have enough space to install the speed domes and its accessories.
3. Check the intensity of conformation at the installation scene. Please make sure that the endure ability of ceilings or walls is
4 times as the weight of speed dome and its accessories.
4. Preparation of cables
- Choose the video cable according to the transmission length. The video should meet the least demands as:
1. 75Ω resistance
2. 100% copper core conducting wire.
3. 95% weaving copper shield.
- RS485 communication cable, please refer to Appendix 2
- 4V AC power cable, please refer to Appendix 3
5. Please keep all wrappers
Please keep all wrappers after unpack them for future use. In case of any failure occurred, please return the speed dome to
the factory with the original wrapper.
Note: Transportation without the original wrapper may result in damage on the speed dome and cost additional charge.
SAFETY INSTRUCTIONS FOR INSTALLERS
- Carefully read the instructions on this leaflet: they give important information on the safety, use and maintenance of the in-
stallation.
- After removing the packing, check the integrity of the set. Packing components (plastic bags, expanded polystyrene etc.) are
dangerous for children. Installation must be carried out according to national safety regulations.
- It is convenient to fit close to the supply voltage source a proper bipolar type switch with 3 mm separation (minimum) bet-
ween contacts.
- Before connecting the set, ensure that the data on the label correspond to those of the mains.
- This apparatus must only be used for the purpose for which it was expressly designed, e.g. for audio or video door entry sy-
stems. Any other use may be dangerous. The manufacturer is not responsible for damage caused by improper, erroneous or
irrational use.
- Before cleaning or maintenance, disconnect the set.
- In the event of faults and/or malfunctions, disconnect from the power supply immediately by means of the switch and do not
tamper with the apparatus.
- For repairs apply only to the technical assistance centre authorized by the manufacturer.
- Safety may be compromised if these instructions are disregarded.
- Do not obstruct opening of ventilation or heat exit slots and do not expose the set to dripping or sprinkling of water. No ob-
jects filled with liquids, such as vases, should be placed on the apparatus.
- Installers must ensure that manuals with the above instructions are left on connected units after installation, for users' infor-
mation.
- All items must only be used for the purposes designed.
- WARNING: to prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
- This leaflet must always be enclosed with the equipment.
Directive 2002/96/EC (WEEE)
The crossed-out wheelie bin symbol marked on the product indicates that at the end of its useful life, the product must
be handled separately from household refuse and must therefore be assigned to a differentiated collection centre for elec-
trical and electronic equipment or returned to the dealer upon purchase of a new, equivalent item of equipment.
The user is responsible for assigning the equipment, at the end of its life, to the appropriate collection facilities.
Suitable differentiated collection, for the purpose of subsequent recycling of decommissioned equipment and environmentally
compatible treatment and disposal, helps prevent potential negative effects on health and the environment and promotes the
recycling of the materials of which the product is made. For further details regarding the collection systems available, contact
your local waste disposal service or the shop from which the equipment was purchased.
Risks connected to substances considered as dangerous (WEEE).
According to the WEEE Directive, substances since long usually used on electric and electronic appliances are considered
dangerous for people and the environment. The adequate differentiated collection for the subsequent dispatch of the appliance
for the recycling, treatment and dismantling (compatible with the environment) help to avoid possible negative effects on the
environment and health and promote the recycling of material with which the product is compound.
GB
34