Art. 52WS/4 Net Video Server INSTALLATION AND OPERATION MANUAL Product is according to EC Directive 2004/108/CE, 2006/95/CE and following norms. GB Cod. S6I.52W.S4E RL.
GB 52WS/4 INDEX CHAPTER 1 INTRODUCTION.................................................................................................................. 3 1.1 52WS/4 FUNCTIONS AND FEATURES.................................................................................................3 1.2 COMMON APPLICATION.................................................................................................................. 3 CHAPTER 2 INSTALLATION..............................................................
52WS/4 Chapter 1 GB Introduction 52WS/4 net video server adopts embedded Linux operation system (RTOS) and TI DaVinci processor that is completely independent of PC platform, and efficiently improves system performance. Firmware is burned into the FLASH, making the system more steady and reliable. 52WS/4net video server has the function of compressing the video signal and audio signal simultaneously into H.
52WS/4 GB Chapter 2 Installation 2.1 Hardware installation 2.1.1 Installation steps 1. Open packing case, and check the integrity; 2. Take out things needed during installation; 3. Connect cables needed (video signal input cable, audio signal input cable, RS485 cable and cable for LAN); 4. Take out stabilizer power supply and power on. 2.1.2 Installation notice Please read the following notice carefully. If you have any question, please contact us. Notice: 1.
2WS/4 GB Back panel: 1 2 3 4 6 7 5 Interface Instruction (From left to Right in return): 1. Power jack is connected with 12V direct current through voltage stabilizer; Please use the stabilizer power supply correctly; 2. UTP network connector; 3. 4 external alarm input and 2 relay output; 4. Standard RS-485 serial port RJ45 socket and Standard RS-232 serial port RJ45 socket; 5. 4 channels video input and audio input; 6. One line in audio input 7. One audio output. 2.
GB 52WS/4 (2) 25-pin to 9-pin converter’s internal connection is like this: 6/12
52WS/4 GB (3) If you don’t want to use 25-pin to 9-pin convertor to connect DVS and DTE through RS232 interface, you must use RJ45-DB9 cable. Its internal connection description is: (4) When the RS232 interface of the DVS connects with the DCE (such as MODEM), one end of the cable is the 8-pin RJ45 connector and the other is the DB25 male connector.
GB 52WS/4 2.3.2 PIN definition of RS485 serial interface 2.3.
52WS/4 Chapter 3 GB Configuration via Web browser Before visit the camera via web browser, user should adjust security level. Open the web browser, and enter the menu “Tool/ internet option/Security/Custom level”, then set the security level to Security Level - Low, or enable ActiveX Control and the Plug-in directly. Figure 3.2.1 gives you a visual illustration. After you can see the camera video, recover the security level for security.
GB 52WS/4 The default IP of the camera is 192.0.0.64 with 8000 as the default port, admin as the administrator, and 12345 as the password. The administrator can create up to 15 separate operators with different right levels. To login the camera through IE, input the IP address in the address column, and the “Login” dialog box will pop-up as Fig. 3.2.2. Input your user name and password, and then click “Login” to enter the “preview” page.
NOTE Chapter 4 Frequent ask questions 1, Failure to control PTZ It is possible that the camera and equipment are not connected through RS485 port, or the wrong configuration of the decoder.
SAFETY INSTRUCTIONS FOR INSTALLERS - Carefully read the instructions on this leaflet: they give important information on the safety, use and maintenance of the installation. - After removing the packing, check the integrity of the set. Packing components (plastic bags, expanded polystyrene etc.) are dangerous for children. Installation must be carried out according to national safety regulations.
