User's Manual
Infant Protection Bracelet – User Guide _____________________________________________________________________________________________
Electrical Specifications
Supervision
Transmissions Rates:
IR: 5sec in motion 300sec motionless / RF:10sec in motion. 60sec motionless
RF Transmission Rate
upon entry into LF area
Burst of 43messages (each lasting @ 2ms) with intervals of between 200 and 400ms, and the
total burst time not exceeding 1 second
Events:
Band Closed (B2 up)
Band Opened (B2 down)
LF & Tamper
Single burst of 43messages (each lasting @ 2ms) with intervals of between 200 a 400ms, and
the total burst time not exceeding 1 second
LF and Tamper Check Every 250ms
Power Source One Lithium Ion battery
Battery Life For tag in motion 7hrs per day, 3 year for RF only tag, 2 year for RF/IR
Green LED Indicator
Operational Mode: Flashes once every 15 seconds
Disposable Band Removed/Connected: Rapidly flashes 4 times
Hibernation Mode: Not Lit
RED LED Indicator Low Battery: Flashes once every second
Badge ID code Unique factory programmed ID
General Specifications
Construction Grilamid Nylon
Physical Dimensions 39.4 X 31.5 X 14.8 mm (1.55 x 1.24 x 0.582 inches)
Weight (assembled) 20 grams (0.75 ounces) approximate
Temperature & Humidity Temp: -10°C to 70°C (14°F to 158°F), Humidity: 20% to 80% non-condensing
Water Rated Enclosure Tag: IP-66 / Complete Bracelet: IP-55
Warranty One year limited warranty (excluding battery)
Compliance Standards
EN301 489-1, EN301 489-3, EN 60601-1-2,CISPR 11, IEC61000-4-2, IEC61000-4-3,
EN300 220-1, EN300 220-2, FCC Part 15.231 Level C, FCC ID: O4X5--BTD00433 IC:1467G-
BTD00433
Ordering Details
Part Information
5-BTC20433 Reuseable Tag, WR, IR/RF/LF, 433 MHz
5-BTC20433-1 Reuseable Tag, WR, RF/LF, 433 MHz
Accessories
5-BTC90001-1 Disposable Tamper Band, Pediatric, 24cm maximum diameter, (25 units)
5-BTC90001 Disposable Tamper Band, Infant, 16cm maximum diameter, (50 units)
5-BTC90003 Extractor, Infant (10 units)
5-BTC90006 Grip key w/lanyard (set of 5)
Standards Compliance
This device complies with Part 15 of the FCC Rules; and its operation is
subject to the following two conditions:
• This device may not cause harmful interference
• This device must accept any interference received, including interference
that may cause undesired operation.
For a Class B digital device or peripheral, the instructions furnished the user
shall include the following or similar statement, placed in a prominent
location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning!
Changes or modifications to this equipment not approved by the party
responsible for compliance (Visonic Technologies Ltd.) could void the user’s
authority to operate the equipment.