USER MANUAL Elo Touch Solutions IDS ET3203L/ET4303L/ET5053 Display User Manual – IDS ET3203L/ET4303L/5053 UM600265 Rev.
Copyright © 2020 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice.
Table of Contents Section 1: Introduction ............................................................................................................................................................................................................................... 4 Section 2: Unpacking ..............................................................................................................................................................................................................................
Section 1: Introduction Product Description Your new Interactive Digital Signage (IDS) Display combines Elo Touch Solutions reliable performance with the latest developments in touchscreen technology and display design. This combination of features creates a natural flow of information between a user and the IDS Display.
Section 2: Unpacking Unpacking the Interactive Digital Signage (IDS) Display To unpack the IDS, follow these steps: 1. The carton should be oriented in the manner according to its labeling. The hinged plastic locks should be at the ‘bottom’. 2. Unlock and remove all 4 hinged plastic locks. User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
3. Once the locks are removed, lift the cartons top lid off the bottom frame. 4. With the top lid removed, you now have access to the IDS Display and the included accessories. Verify that the box contains: • IDS ET3203L/ET4303L/ET5053L IDS Display: • HDMI 2.0 cable • USB-C cable (Type A plug to Type C plug) • power cable, IEC 60320-C13 to NA plug • power cable, IEC 60320-C13 to EU/KR plug • power cable, IEC 60320-C13 to UK plug • Serial 3.
Section 3: IDS Display Installation IDS Display: Connecting to an External Computer Source from HDMI or DisplayPort 1. Connect the included HDMI cable (or your own or DisplayPort cable) between the monitor and the video source. 2. Connect the USB-C (Type A plug to Type C plug) touch cable between the monitor and your host PC. 3. Select the correct power cable for your region. Connect the cable from the IDS Display POWER IN connector to the AC power source. 4.
IDS Display: Connecting to the Elo Computer Module (ECM) 1. Remove the cover in order to expose the computer module docking area. 2. Slide the Elo Computer Module into the bay and secure the ECM with the locking screws. a. Note: The ECM can be plugged in while there is power to the monitor. 3. As soon as video is detected, the monitor will begin to display the content. Visit the Elo Touch Solutions website www.elotouch.
Section 4: Mounting Information Note: It is strongly recommended that at least two people handle, lift, or move the IDS Display. Note: Do not leave the IDS Display facing down for long periods of time as this will cause permanent damage to the LCD panel. Mounting Orientations The following mounting orientations are supported: landscape, portrait, tabletop and tilt.
Portrait Orientation When rotating the IDS Display to portrait orientation, ensure that the Elo logo appears in the same location as the pictures below. The IO ports will be located at the bottom. Tabletop When the IDS Display is used in tabletop application, support the IDS Display using the VESA mounting pattern on the rear to support the weight of the IDS Display. Additional support around the edge may also be added if desired to maintain flatness of the touch screen.
Tilt Mode The IDS Display can support a tilt of 15º. 15 degrees max User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
Rear VESA Mount A four-hole, 400x400mm mounting pattern is provided on the rear of the IDS Display. The VESA FDMI-compliant mounting is coded - VESA MOUNT PER MIS-F, 400 x 400mm, M6 Refer to www.elotouch.com for dimensional drawings. Optional Mounting Methods An optional low profile stand kit and wall-mount kit are available for the IDS ET3203L/ET4303L/ET5053L Displays. Detailed information is available on the marketing specification drawing at www.elotouch.com.
Section 5: Operation Power To turn the IDS Display on or off, press the power button once. If a computer module is installed, then the computer module will also turn on with the monitor. For proper shut down of the computer module, follow the computer modules operating systems normal power off procedure. The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications available on the Elo website www.elotouch.com.
Video Information An LCD panels native resolution is its width and height measured in number of pixels. In almost all cases, an image displayed on an LCD monitor will look best when your computers output resolution matches the LCD panels native resolution. See the display specifications on the Elo website www.elotouch.com to find your IDS Displays native resolution. Operating in other resolutions will degrade video performance and is not recommended.
On Boot Up Parameter Let’s Get Started Video Port Discovery Brightness Brightness Sensor Contrast Black Level Video Sharpness Available Adjustment On first boot up, the Language, Time and Time Zone must be selected When enabled, the monitor will automatically switch if a new video port is connected. Default: Enabled Adjust the brightness of the display. Default: 80 The light sensor can be toggled on or off. When the light sensor is enabled, the brightness cannot be changed manually.
HDMI Full Color Range Audio Default: Standard When enabled, displays full color range of HDMI (0-255) When disabled, displays the legacy color range (16-255) Default: enabled Audio Input: Sets where audio should play from When set to Internal-PC, the audio comes out from the line out on the ECMG4 (ECM Docking) When set to Monitor, the audio comes out from the video source on the monitor Audio Output: Sets where audio should play for When set to Speaker, the audio output to the speaker Audio Selections Wh
Recall Defaults OSD Timer OSD Language On Screen Display OSD Lock OSD Portrait Rotation Touch Switch Tabletop Monitor Information Information System Temperature Help & Support User Manual – IDS ET3203L/ET4303L/ET5053L Off: 01:00:00 On: 07:00:00 Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable parameters (except OSD Language and OSD Time Settings) and for Preset Video Mode timings.
On-Screen Display (OSD) (Optional Elo Part Number – E483757) Connected Through the RJ45 Connection Five OSD buttons can be found on the OSD remote. There is an LED light which shows the current state of the monitor. The following are the functions that relate to the designated button. Note: Opening the OSD menu from the remote will disable the touch functions on the OSD menu.
Audio Audio can be output from the following locations: 1. From the IDS Display speakers via the video channel 2. The Line Out port on the IDS IO ports 3. From the computers Line Out port (If an Elo Computer Module is installed) See the “Audio” OSD parameter for details. Note: When headphone is plugged into the headphone output jack, the internal speakers turn off and audio is played over the headphone. Volume and muting of the speaker and headphone outputs are controlled by the OSD.
Example: Have the monitor ON for Monday, Wednesday and Friday between 9:00AM and 5:00PM. All other days and time, the monitor shall be OFF. o Enable the On/Off Schedule o Select M W F o Set the ON time for 09:00:00 and the OFF time for 17:00:00 *Note that all of time settings operate on the 24-hour clock. Wake-On-Touch The touch display supports wake-on-touch functionality when the PC is in sleep mode. To enable this, please ensure that the BIOS settings have enabled USB support during the S4 sleep cycle.
Changing the factory default picture settings or enabling other features will increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR rating. For more information on the ENERGY STAR program, refer to energystar.gov. Stylus (Active and Passive) (Optional) Elo provides active stylus pens that can be used on the projected capacitance version of the monitor.
Elo Edge Connect micro-USB peripheral ports Available on all four sides of the monitor. The micro USB ports are designed for Elo’s optional peripherals. See www.elotouch.com for the optional peripherals that work with the IDS ET3203L/ET4303L/ET5053L display.
Section 6: Maintenance Information To avoid risk of electric shock, follow all safety notices and do not disassemble the IDS Display or Computer Module. They are not user serviceable. Do not block or insert anything inside any of the ventilation slots. The IDS Display is equipped with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord.
Section 7: Technical Support Technical Assistance Technical Specifications Support visit www.elotouch.com/products for technical specifications for this device visit www.elotouch.com/support for technical support Refer to last page for worldwide technical support phone numbers. User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
Section 8: Regulatory Information Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit www.elotouch.com/e-waste-recycling-program/.
This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada. CAN ICES3(A)/NMB3(A) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
iv. Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits. v. Disconnect and remove any I/O cables that the digital device does not use. (Unterminated I/O cables are a potential source of high RF emission levels.) vi. Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.
China RoHS In accordance to Chinese law (Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products), the section below lists out the name and amount of the toxic and/or hazardous materials that this product may contain.
Power Specifications Electrical Ratings Input 100 - 240 VAC 50/60Hz Operating & Storage Conditions Operating Conditions Temperature Portrait/Landscape/Tilt (≤15°) 0°C - 40°C / 32°F to 104°F Tabletop 0°C - 35°C / 32° F to 95° F Humidity 20% to 80% (non-condensing) Storage Conditions Temperature -20°C - 60°C / -4° F to 140° F Humidity 10% to 95% (38.7° C max wet bulb temperature) User Manual - IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
Section 9: Warranty Information For warranty information, go to http://support.elotouch.com/warranty/ User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
Section 10: Appendix A Light Sensor Curve Brightness Curve 300 250 Brightness 200 150 100 50 0 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 100 Light Sensor Value User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
Color Sensor The color sensor functions according to the following chart: User Manual – IDS ET3203L/ET4303L/ET5053L UM600265 Rev.
www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers • IDS Display Newsletter To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 customerservice@elotouch.com Europe Tel +32 (0)16 70 45 00 Fax +32 (0)16 70 45 49 elosales@elotouch.
