USER MANUAL Elo Touch Solutions IDS ET6553L/ET5553L Display User Manual – IDS ET6553L/ET5553L UM600326 Rev C page 1 of 38
Copyright © 2019 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice.
Table of Contents Section 1: Introduction ............................................................................................................................................................................................................................... 4 Section 2: Unpacking ..............................................................................................................................................................................................................................
Section 1: Introduction Product Description Your new Interactive Digital Signage (IDS) Display combines Elo Touch Solutions reliable performance with the latest developments in touchscreen technology and display design. This combination of features creates a natural flow of information between a user and the IDS Display. This IDS Display incorporates a 10-bit color, active matrix thin-film-transistor, and digital signage LCD panel to provide superior display performance.
Section 2: Unpacking Unpacking the Interactive Digital Signage (IDS) Display To unpack the IDS, follow these steps: 1. The carton should be oriented in the manner according to its labeling. The hinged plastic locks should be at the ‘bottom’. 2. Open and remove all 4 hinged plastic locks.
3. Once the locks are removed, lift the cartons top lid off the bottom frame. 4. With the top lid removed, you now have access to the IDS Display and the included accessories.
Verify that the box contains: • IDS ET6553L/ET5553L IDS Display: • HDMI 2.0 cable • USB 3.0 cable (Type A plug to Type B plug) • power cable, IEC 60320-C13 to NA plug • power cable, IEC 60320-C13 to EU/KR plug • power cable, IEC 60320-C13 to UK plug • Serial 3.5mm male to Serial DB9 female cable • Energy label according to EU Regulation 1062/2010 • 2x Stylus Active or Passive depending on the monitors touch technology.
Section 3: IDS Display Installation Connector Panel and Interfaces Remove the cable cover located on the back-right side of the IDS Display (when viewed in landscape orientation) to access the connector panel.
IDS Display: Connecting to an External Computer 1. Connect the included HDMI cable (or your own or DisplayPort cable) between the monitor and the video source. 2. Connect the USB touch cable between the monitor and your host PC. 3. Select the correct power cable for your region. Connect it between the AC power source and the IDS Display POWER IN connector. 4. As soon as power is detected, the monitor will turn on. 5.
IDS Display: Connecting to the Elo Computer Module (ECM) 1. Remove the cover in order to expose the computer module docking area. 2. Slide the Elo Computer Module into the bay and secure the ECM with the locking screws. 3. Select the correct power cable for your region. Connect it between the AC power source and the IDS Displays POWER IN connector. a. Note: The ECM can be plugged in while there is power the monitor. 4. As soon as video is detected, the monitor will begin to display the content. 5.
Section 4: Mounting Information Note: It is strongly recommended that at least two people handle, lift, or move the IDS Display. Note: Do not leave the IDS Display facing down for long periods of time as this will cause permanent damage to the LCD panel. Mounting Orientations The following mounting orientations are supported: landscape and portrait. Landscape Orientation When mounting the IDS Display in landscape orientation, ensure that the Elo logo appears in the same location as the pictures below.
Portrait Orientation When rotating the IDS Display to portrait orientation, ensure that the Elo logo appears in the same location as the pictures below. The IO ports will be located at the bottom. Rear VESA Mount A four-hole, 600x600mm and 400x400mm mounting pattern is provided on the rear of the IDS Display. The VESA FDMI-compliant mounting are coded - VESA MOUNT PER MIS-F, 400 x 400mm, M6 - VESA MOUNT PER MIS-F, 600 x 600mm, M8 Refer to www.elotouch.com for dimensional drawings.
Optional Mounting Methods An optional low profile wall-mount kit is available for the IDS ET6553L/ET5553L Displays. Detailed information is available on the marketing specification drawing at www.elotouch.com. Elo Low Profile Wall Mount kit: P/N E282876 and Drawing MS602094 for IDS ET6553L P/N E727774 and Drawing MS602320 for IDS ET5553L Consult the wall mount user guide for detailed installation information.
1. Remove the mounting screw from the lower left speaker and slide the speaker downward to disengage the mounting hooks. Pull the speaker downward enough so the cable connector is exposed and disengage the connector. Cable Connector 2. Remove the mounting screw from the mounting cover on the top right of the IDS Display and slide the cover downward to disengage the mounting hooks.
3. Install the speaker into the new location by connecting the speaker cable connector and then feeding the connector into the hoe in the back cover whole sliding the speaker down from the top so both hooks are engaged with the slots in the back cover. Reinstall the mounting screw. Slide cable connector into this hole 4. Install the cover removed in step 2 in the old speaker location by sliding it in so the hooks engage the slots in the back cover and then install the mounting screw.
Section 5: Operation Power To turn the IDS Display on or off, press the power button once. If a computer module is installed, then the computer module will also turn on with the monitor. To gracefully shut down the computer module, follow the computer modules operating systems normal power off procedure. The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications available on the Elo website www.elotouch.com.
Video Information An LCD panels native resolution is its width and height measured in number of pixels. In almost all cases, an image displayed on an LCD monitor will look best when your computers output resolution matches the LCD panels native resolution. See the display specifications on the Elo website www.elotouch.com to find your IDS Displays native resolution. Operating in other resolutions will degrade video performance and is not recommended.
On Boot Up Parameter Let’s Get Started Video Port Discovery Brightness Brightness Sensor Contrast Black Level Video Sharpness Available Adjustment On first boot up, the Language, Time and Time Zone must be selected When enabled, the monitor will automatically switch if a new video port is connected. Default: Enabled Adjust the brightness of the display. Default: 100 The light sensor can be toggled on or off. When the light sensor is enabled, the brightness cannot be changed manually.
Picture Modes HDMI Full Color Range If the color space is YUV mode, then Hue and Saturation can be varied in this menu. Preset color modes that change the color parameters to enhance color definitions.
Recall Defaults OSD Timer On Screen Display OSD Language OSD Lock OSD Portrait Rotation Monitor Information Information System Temperature Help & Support User Manual – IDS ET6553L/ET5553L Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable parameters (except OSD Language and OSD Time Settings) and for Preset Video Mode timings. Adjusts how long a period of OSD button inactivity the IDS Display will wait before closing the OSD.
On-Screen Display (OSD) - Connected Through the RJ45 Connection Five OSD buttons can be found on the OSD remote. There is an LED light which shows the current state of the monitor. The following are the functions that relate to the designated button. Note: Opening the OSD menu from the remote will disable the touch functions on the OSD menu.
Audio Audio can be output from the following locations: 1. From the IDS Display speakers via the video channel 2. The Line Out port on the IDS DIsplay IO ports 3. From the computers Line Out port (If an Elo Computer Module is installed) See the “Audio” OSD parameter for details. Note: When headphones are plugged into the headphone output jack, the internal speakers turn off and audio is played over the headphones. Volume and muting of the speaker and headphone outputs are controlled by the OSD.
Real Time Clock (RTC) Functionality This IDS Display has real time clock functionality. In the OSD menu, there is a sub-menu called RTC Settings. To utilize the RTC functionality: The user must set up the Time setting for their specific time zone. When the On/Off Schedule is Enabled, the user can choose when to leave the monitor on and when it should be off. Individual or multiple days can be chosen. Example: Have the monitor ON for Monday, Wednesday and Friday between 9:00AM and 5:00PM.
Energy Saving Mode IDS ET6553L can meet Energy Star 7.1 requirements, if Energy Saving Mode is enabled. IDS ET5553L can meet Energy Star 8.0 requirements, if Energy Saving Mode is enabled. When Energy Saving Mode is enabled, four side peripheral ports, MDC command and Auto Display Wake Up function will be limited. To restore full functionality of the IDS Display, disable the Energy Saving Mode. ENERGY STAR is a program run by the U.S. Environmental Protection Agency (EPA) and U.S.
Elo Edge Connect micro-USB peripheral ports Available on all four sides of the monitor are microUSB ports designed for Elo’s optional peripheral ports. See www.elotouch.com for the optional peripherals that work with the IDS ET6553L/ET5553L display. The pinout is as follows: Pin1: 5V Power Pin2: USB DPin3: USB D+ Pin4: PWM control for camera module Pin5: Ground Conference Camera (Optional) Elo provides an optional camera module (P/N E277819) which has a built-in microphone and proximity detection sensor.
Section 6: Maintenance Information To avoid risk of electric shock, follow all safety notices and do not disassemble the IDS Display or Computer Module. They are not user serviceable. Do not block or insert anything inside any of the ventilation slots. The IDS Display is equipped with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord.
Section 7: Technical Support Technical Assistance Technical Specifications Support visit www.elotouch.com/products for technical specifications for this device visit www.elotouch.com/support for technical support Refer to last page for worldwide technical support phone numbers.
Section 8: Regulatory Information Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit www.elotouch.com/e-waste-recycling-program/.
Notice to Users in Canada: This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada. CAN ICES3(A)/NMB3(A) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
1. In order to meet emission and immunity requirements, the user must observe the following: a. Use only the provided I/O cables to connect this digital device with any computer. b. To ensure compliance, use only the provided manufacturer’s approved line cord. c. The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2.
Agency Certifications The following certifications and marks have been issued or declared for the IDS ET6553L/ET5553L monitor: • UL, FCC (US) - Class A • cUL, IC (Canada) • CB (International safety) • CE (Europe) - Class A • RCM (Australia) • VCCI (Japan) • CCC (China) (for TouchPro version only) User Manual – IDS ET6553L/ET5553L UM600326 Rev C, page 31 of 38
China RoHS In accordance to Chinese law (Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products), the section below lists out the name and amount of the toxic and/or hazardous materials that this product may contain.
Explanation of Markings In accordance with the SJ/T11364 requirement, electrical and electronic products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets. Operating Temperature: See table on next page.
Power Specifications Electrical Ratings Input 100 - 240 VAC 50/60Hz Operating & Storage Conditions Operating Conditions Temperature 0°C - 40°C Humidity 20% to 80% (non-condensing) Storage Conditions Temperature -20°C - 50°C Humidity 10% to 95% (non-condensing) User Manual - IDS ET6553L/ET5553L UM600326 Rev.
Section 9: Warranty Information For warranty information, go to http://support.elotouch.com/warranty/ User Manual – IDS ET6553L/ET5553L UM600326 Rev.
Section 10: Appendix A Light Sensor Curve Brightness Curve 300 250 Brightness 200 150 100 50 0 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 100 Light Sensor Value User Manual – IDS ET6553L/ET5553L UM600326 Rev.
Color Sensor The color sensor functions according to the following chart: User Manual – IDS ET6553L/ET5553L UM600326 Rev.
www.elotouch.com Visit our website for the latest • Product Information • Specifications • Upcoming Events • Press Releases • Software Drivers • IDS Display Newsletter To find out more about our extensive range of Elo touch solutions, go to www.elotouch.com, or call the office nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 customerservice@elotouch.com User Manual – IDS ET6553L/ET5553L Europe Tel +32 (0)16 70 45 00 Fax +32 (0)16 70 45 49 elosales@elotouch.
