Assembly Instructions Wall Mount Kit for Elo 5553 IDS Display Revision A P/N UM600336
Safety Warning: Do not install this equipment on any wall or structure that is not capable of supporting four times the weight of the IDS Display, brackets, and any accessories attached to it. The 5553L monitor weighs in excess of 85.8lbs (390.8kg) with the optional Elo computer module. 85.8lbs x 4 = 343.2lbs (155.6kg). Do not leave out any required parts or leave the monitor on the wall unattended without securely fastening all brackets and screws as instructed in this document.
Kit Contents Upper Display Bracket, (x1) Lower Display Bracket with hinged cable service support bracket, (x2) Upper Wall Bracket, (x1) Lower Wall Bracket, (x1) M8X25 Phillips head screw (x4) M4X10 Phillips head screw (x4) 1/4” x 1-/2” hex head wood screw (x6) 1/4” Heavy Duty Toggle Anchor (x6) (Additional anchors available P/N Toggler 25014) 1/4-20 x 2-1/2” hex head machine screw (x6) 5/16” x 2-1/2” Concrete Sleeve Anchor (x6) 1/4-20 thread size, m inimum pullout strength rating = 1500lbs
Step 1:Place the IDS face down on a padded surface and then install the upper and lower display brackets following step 2a or 2b. Step 2a: Attach upper and lower display brackets (Landscape orientation) • Secure the upper display bracket to the upper mounting pads using two M8x25 screws. • Secure the lower display brackets to the two lower mounting location using two M8x25 screws. Ensure the hinged cable service brackets are oriented as shown. • Proceed to step 3.
Step 2b: Attach upper and lower display brackets (portrait orientation) • Secure the upper display bracket to the upper mounting pads using two M8x25 screws. • Secure the lower display brackets to the two lower mounting locations using one M8x25 screw and 1 m4x10 screw on each bracket. Ensure the lower display brackets are oriented as shown. • Proceed to step 3.
Step 2c: Install security screws • Loosely install two M4x10 screws on the lower brackets making sure to leave 5mm (1/4”) of space under the screw head. To ensure that the screws are accessible after the IDS is mounted on the wall, use position A for landscape orientation and Position B for portrait orientation.
Step 3: Position the wall brackets • Choose a suitable location to mount the IDS Display using the included dimensional drawings. You may wish to mark the IDS Display outline with masking tape (not included) and draw a vertical reference line from the top of the display outline to the bottom ensuring the line is plumb. • Center the upper wall bracket over the reference line so the top of the triangular hole intersects the reference line.
Step 4: Attach upper and lower wall brackets • The upper wall bracket must be secured with four 1/4” or M6 screws (minimum) • The lower wall bracket must be secured with two 1/4” or M6 screws (minimum) • The wall mount kit includes screws for wood and metal stud walls, concrete, and solid wood. Both brackets must be mounted to structurally sound parts of the wall. Do not install on drywall without proper structure behind it. Installer must follow all applicable building codes when installing this kit.
Step 4: Attach IDS Display to wall brackets • Elo recommends at least two people lift the IDS display onto the wall mount brackets. • Tilt the monitor slightly back while lifting it onto the upper wall bracket. Ensure both pivot screws on the upper monitor bracket are engaged in the hooks on the upper wall bracket. You should be able to pivot the bottom of the IDS Display forward a few inches when correctly installed.
Step 5: Secure IDS Display to lower wall bracket (all configurations) • Pivot the bottom of the IDS display forward slightly and rotate the cable service brackets upward against the back of the IDS display while pivoting the IDS display back against the wall. • Use a long Phillips head screw driver to tighten the M4 screws from the bottom side of the IDS display when mounted in landscape orientation.
Connecting or diconnecting cables or ECM while IDS Display is mounted • Loosen the M4 screws tightened in step 5 by several complete turns so there is 3-4mm of space under the heads. Then pivot the bottom of the display forward several inches until the cable service brackset pivot down automatically. The brackets can also be rotated down by hand. Then lower the bottom of the display so the cable service bracket touches the lower wall bracket.
Removing the IDS Display from the wall bracket (all configurations) • Use a long Phillips head screw driver to loosen the M4 screws from the bottom side of the IDS display when mounted in landscape orientation. (Portrait mounted IDS Displays require access from the left and right side) • Tilt the bottom of the IDS Display forward a few inches while lifting up and off the wall bracket.